Sponsored Content
Operating Systems SCO Problems with network card in SCO Post 302381320 by jgt on Thursday 17th of December 2009 09:18:15 PM
Old 12-17-2009
Quote:
Error: Cannot find Driver.o for sem.
Fatal Error: Erros encountered. Configuration Terminated.
idbuild: idconfig had errors
system build failed
Until you resolve this problem, the kernel re-link will not complete, and you will always be re-booting the original.
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But... (0 Replies)
Discussion started by: DPAI
0 Replies

3. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

4. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies

5. SCO

3c905b network card problem with SCO 5.0.5

Hi, I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies

6. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

7. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

8. SCO

network problems with sco

SCO unix 5.0.5 - Suddently network lost & has to be reboot. I try to stop TCP & start TCP. but no connection. Any idea about that. thanks (8 Replies)
Discussion started by: ajantha
8 Replies

9. Solaris

Network Card Name details

Hi All, Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ? This is such a basic question which i always overlooked :( Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies

10. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
TIFFWriteDirectory(3tiff)				 Introduction to Library Functions				 TIFFWriteDirectory(3tiff)

NAME
TIFFWriteDirectory - write the current directory in an open TIFF file SYNOPSIS
#include <tiffio.h> int TIFFWriteDirectory(TIFF* tif) DESCRIPTION
Write the contents of the current directory to the file and set up to create a new subfile in the same file. Applications only need to call TIFFWriteDirectory when writing multiple subfiles to a single TIFF file. TIFFWriteDirectory is automatically called by TIFFClose and TIFF- Flush to write a modified directory if the file is open for writing. EXTENDED DESCRIPTION
Diagnostics All error messages are directed to the TIFFError(3tiff) routine. Error post-encoding befoBeforeecwritingitthe contents of the current directory, any pending data is flushed. This message indicates that an error occurred while doing this. Error flushing data befoBeforeewritingrthe.contents of the current directory, any pending data is flushed. This message indicates that an error occurred while doing this. Cannot write directory, Therefwasanot enough space to allocate a temporary area for the directory that was to be written. Error writing directory Aowrite error occurred when writing the count of fields in the directory. Error writing directory Aowriteserror occurred when writing the directory fields. Error writing directory Aiwrite error occurred when writing the link to the next directory. Error writing data for fAewriteserror occurred when writing indirect data for the specified field. Error writing TIFF headeA.write error occurred when rewriting header at the front of the file. Error fetching directoryAcread.error occurred when fetching the directory count field for a previous directory. This can occur when setting up a link to the directory that is being written. Error fetching directoryAlread error occurred when fetching the directory link field for a previous directory. This can occur when setting up a link to the directory that is being written. RETURN VALUES
1 is returned when the contents are successfully written to the file. Otherwise, 0 is returned if an error was encountered when writing the directory contents. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWTiff | +-----------------------------+-----------------------------+ |Interface stability |External | +-----------------------------+-----------------------------+ SEE ALSO
libtiff(3), TIFFError(3tiff), TIFFOpen(3tiff), TIFFReadDirectory(3tiff), TIFFSetDirectory(3tiff) NOTES
This man page was originally written by Sam Leffler. Updated by Breda McColgan, Sun Microsystems Inc., 2004. SunOS 5.10 05 Apr 2004 TIFFWriteDirectory(3tiff)
All times are GMT -4. The time now is 10:39 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy