Dear all,
Please advise what approach can remove all line break from a text file?
e.g.
Source file:
A
B
C
Target file:
A, B, C
Thanks,
Rock (5 Replies)
hi All,
Have a doubt in ksh..Am not familiar with arrays but i have tried out a script..
plzzzzz correct me with the script
My i/p File is:
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS =
(PROTOCOL = TCP)
(Host = 192.168.2.2)
(Port = 1525)
)
)
(CONNECT_DATA = (SID = TESTDB1)
)
)
... (7 Replies)
Hi
Is there any command where we can insert a line "2|||" before every line starting with "3|"
my input is as follows
1|ETG|12345
3|79.58|||GBP||
1|ETG|12345
3|79.58|||GBP||
1|ETG|12345
2|EN_GB||Electrogalvanize 0.5 m2 ( Renault )
1|ETG|12345
3|88.51|||GBP||
desired output... (10 Replies)
Friends ,
I have a large file and i need to insert a line after every line.I am actually unaware how to do it.Any help appreciated.
My File
control station *ATM* , qread $OSS.Jul13A.FI01 interval 1 intcount 1
control station *ATM* , qread $OSS.Jul13A.FI02 interval 1 intcount... (4 Replies)
...when the lines use both a colon and commas to separate the parts you want read as information.
The first version of this script used cut and other non-Bash-builtins, frequently, which made it nice and zippy with little more than average processor load in GNOME Terminal but, predictably, slow... (2 Replies)
I cannot seem to get this to work..
I have a file which has about 100 lines, and there is no end of line (line break \n) at the end of each line, and this is causing problem when i paste them into an application.
the file looks like this
this is a test
that is a test
balblblablblhblbha... (1 Reply)
So I'm in a Unix class and our assignment was to go into VI and write a script to make this file tree. At the end of it, I'd like it to echo "This is the file tree you've created" then a line break, then . But I'm not sure as to who to do it. Is there a way for when I run it (./filesystem), the... (4 Replies)
Hi All,
Please can you advise/help on the below issue
i did a bcp out of a table, it is having problem of line break such that one line is getting broken in two lines for many records.
eg
Correct format
Line 1: - 000f00000bfe2c2c 000218310300000000GBP GBP 734654 10970.35 ... (3 Replies)
Hello All,
I have following file contents
cat file
#line=aaaaaa
#line=bbbbbb
#line=cccccc
#line=dddddd
line=eeeeee
#comment=11111
#comment=22222
#comment=33333
#comment=44444
comment=55555
Testing script
Good Luck!
I would like to comment line line=eeeeee and insert a new line... (19 Replies)
Hello everyone!
I'm trying to make the below file1 look like file2, can anyone help?
Basically I just hit backspace on every line that starts with a number.
Thanks!
file1:
THIS#IS-IT1
4
THIS#IS-IT2
3
THIS#IS-IT3
2
THIS#IS-IT4
1
Result > file2: (4 Replies)
Discussion started by: demmel
4 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)