Mount old zfs filesystem Post: 302380187

7 More Discussions You Might Find Interesting

1. Solaris

How do I export a zfs filesystem that I created?

I created a zpool and two ZFS volumes in OpenSolaris. I would like both ZFS volumes to be exportable. However, I don't know how to set that up. These are the steps I did: 1) Create the zpool using raidz1 across five disks. I have six disks and created a zpool across 5 of them. c4t0d0...

2. Solaris

Why does the # of blocks change for a file on a ZFS filesystem?

I created a zpool and zfs filesystem in OpenSolaris. I made two NFS mount points: > zpool history History for 'raidpool': 2009-01-15.17:12:48 zpool create -f raidpool raidz1 c4t1d0 c4t2d0 c4t3d0 c4t4d0 c4t5d0 2009-01-15.17:15:54 zfs create -o mountpoint=/vol01 -o sharenfs=on -o...

3. Filesystems, Disks and Memory

Howto Convert a filesystem from Veritas to ZFS?

Hi Folks, Looking for info here more than any actual HowTo, does anyone know if there is an actual way of converting a Veritas or UFS filesystem to ZFS leaving the resident data intact. All that I have been able to find, including the commercial products seem to require the FS backed up from...

4. AIX

Mount Filesystem in AIX Unable to read /etc/filesystem

Dear all, We are facing prolem when we are going to mount AIX filesystem, the system returned the following error 0506-307The AFopen call failed : A file or directory in the path name does not exist. But when we ls filesystems in the /etc/ directory it show -rw-r--r-- 0 root ...

5. Solaris

ZFS Filesystem

Hi, Recently we have new server T5 Oracle. We set up it for our database. For out database files we set one zfs filesystem. When i use iostat -xc the output as below. As you see the value for vdc4 is quite high. extended device statistics cpu device ...

6. Solaris

Extend zfs storage filesystem

Hello, Need to ask the question regarding extending the zfs storage file system. currently after using the command, df -kh u01-data-pool/data 600G 552 48G 93% /data /data are only 48 gb remaining and it has occupied 93% for total storage. zpool u01-data-pool has more then 200 gb...

7. UNIX for Beginners Questions & Answers

How to finish expanding a zfs filesystem?

I have a esxi 6.7 server running a Solaris 10 x86 vm (actually a bunch of them). The VM uses zfs for the pools (of course). I expand the underlying ESX logical disk, for example from 50GB to 100gb, then I set autoexpand=on <pool> that belongs to the esx logical disk. what am i missing to...

LEARN ABOUT NETBSD

mlxctl

MLXCTL(8)						    BSD System Manager's Manual 						 MLXCTL(8)

NAME

     mlxctl -- Mylex DAC960 family management utility

SYNOPSIS

     mlxctl [-f dev] [-v] [-a] status [drive] [...]
     mlxctl [-f dev] [-a] detach [drive] [...]
     mlxctl [-f dev] [-a] check [drive] [...]
     mlxctl [-f dev] rebuild channel:target
     mlxctl [-f dev] cstatus
     mlxctl [-f dev] rescan
     mlxctl [-f dev] config

DESCRIPTION

     The mlxctl utility performs status monitoring and management functions for Mylex DAC960 RAID controllers and attached devices.

     The following options are available:

     -a       Apply the action to all drives attached to the controller.

     -f dev   Specify the control device to use.  The default is /dev/mlx0.

     -v       Increased verbosity.

     The following commands are available:

     cstatus  Display the controller's current status.

     status   Display the status of the specified drives.  This command returns 0 if all drives tested are online, 1 if one or more drives are
	      critical and 2 if one or more are offline.

     rescan   Re-scan the logical drive table, and attach or detach devices from the system as necessary.

     detach   Detach the specified drives.  Drives must be unmounted and unopened for this command to succeed.

     check    Initiate a consistency check and repair pass on a drive that provides redundancy (e.g., RAID1 or RAID5).	This command returns imme-
	      diately.	The status command can be used to monitor the progress of the check.

     rebuild  Rebuild onto the specified physical drive.  Note that there can be only one running rebuild operation per controller at any given
	      time.  This command returns immediately.	The cstatus command can be used to monitor the progress of the rebuild.

     config   Write the current system drive configuration to stdout.

EXAMPLES

     Display the status of drive ld3 attached to the controller mlx1:

	   mlxctl -f /dev/mlx1 -v status ld3

SEE ALSO

     ld(4), mlx(4)

HISTORY

     The mlxctl command first appeared in NetBSD 1.5.3, and was based on the mlxcontrol utility found in FreeBSD.

BUGS

     Modifying drive configuration is not yet supported.

     Some commands do not work with older firmware revisions.

     Error log extraction is not yet supported.

BSD
								  April 10, 2000							       BSD