I created a zpool and two ZFS volumes in OpenSolaris. I would like both ZFS volumes to be exportable. However, I don't know how to set that up.
These are the steps I did:
1) Create the zpool using raidz1 across five disks.
I have six disks and created a zpool across 5 of them. c4t0d0... (3 Replies)
I created a zpool and zfs filesystem in OpenSolaris. I made two NFS mount points:
> zpool history
History for 'raidpool':
2009-01-15.17:12:48 zpool create -f raidpool raidz1 c4t1d0 c4t2d0 c4t3d0 c4t4d0 c4t5d0
2009-01-15.17:15:54 zfs create -o mountpoint=/vol01 -o sharenfs=on -o... (0 Replies)
Hi Folks,
Looking for info here more than any actual HowTo, does anyone know if there is an actual way of converting a Veritas or UFS filesystem to ZFS leaving the resident data intact.
All that I have been able to find, including the commercial products seem to require the FS backed up from... (1 Reply)
Dear all,
We are facing prolem when we are going to mount AIX filesystem, the system returned the following error
0506-307The AFopen call failed
: A file or directory in the path name does not exist.
But when we ls filesystems in the /etc/ directory it show
-rw-r--r-- 0 root ... (2 Replies)
Hi,
Recently we have new server T5 Oracle. We set up it for our database. For out database files we set one zfs filesystem. When i use iostat -xc the output as below. As you see the value for vdc4 is quite high.
extended device statistics cpu
device ... (32 Replies)
Hello,
Need to ask the question regarding extending the zfs storage file system.
currently after using the command, df -kh
u01-data-pool/data 600G 552 48G 93% /data
/data are only 48 gb remaining and it has occupied 93% for total storage.
zpool u01-data-pool has more then 200 gb... (14 Replies)
I have a esxi 6.7 server running a Solaris 10 x86 vm (actually a bunch of them). The VM uses zfs for the pools (of course). I expand the underlying ESX logical disk, for example from 50GB to 100gb, then I set autoexpand=on <pool> that belongs to the esx logical disk.
what am i missing to... (2 Replies)
Discussion started by: mrmurdock
2 Replies
LEARN ABOUT DEBIAN
array-info
array-info(1)array-info(1)NAME
array-info - check the status of a HP (Compaq) SmartArray controller
SYNOPSIS
array-info -d array_device_path [-a|-l|-A|-c|-s|-L|-h]
DESCRIPTION
Array-info is a command line tool to retrieve informations and logical drives status from several RAID controllers (currently HP Compaq IDA
and CISS and MD). It displays informations about the firmware version, Rom revision, number of physical and logical drives on the con-
troller, aswell as the fault tolerance, size, number of physical disks and status for each logical drive.
OPTIONS --device | -d
Path to array device, e.g. /dev/ida/c0d0 or /dev/cciss/c0d1
--all-drives | -a
Show informations about all drives
--logical drive | -l
Show informations about selected logical drive
--show-ctrl | -c
Show informations about controller
--show-logical | -L
Show informations about logical drives
--show-physical | -p
Show physical device informations
--show-status | -s
Show status of logical drives
--show-all | -A
Show all informations
--version | -V
Show version
-h Show help about options
COPYRIGHT
This manual page was written by Raphael Pinson <<raphink@ubuntu.com>>. Permission is granted to copy, distribute and/or modify this docu-
ment under the terms of the GNU General Public License, Version 2 or any later version published by the Free Software Foundation.
2006-12-15 array-info(1)