Sponsored Content
Special Forums IP Networking assign mac address for virtual interface eth1:0 Post 302378536 by Gopi Krishna P on Tuesday 8th of December 2009 06:01:57 AM
Old 12-08-2009
assign mac address for virtual interface eth1:0

Hi ,
by default the physical interface (eth1) and virtual interface eth1:0 will be having same mac address, is there any way we can assign separate mac addresses for both the interfaces.

would some one help me out in this.

Thanks
Gopi
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

How to assign virtual address?.

Hello,I am new to unix,i want to know how to assign virtual ip address to a system that is in my personal network? (1 Reply)
Discussion started by: veeru_jarugula
1 Replies

2. Shell Programming and Scripting

virtual interface

How would i create virtual interface in linux to configure more than one IP address for a physical interface? any help wll be appreciated. https://www.unix.com/images/misc/progress.gif (1 Reply)
Discussion started by: salil2012
1 Replies

3. Solaris

How to assign MAC address to N/W interface in solaris

I m having interface ce0 ce1 and its sub interfaces for that. I want to give MAC addresses for the same. How will I assign it. Please give solution for the same (4 Replies)
Discussion started by: sunray
4 Replies

4. Red Hat

Assign port dedicatedly against an interface !

Dear Friends , I am using RHEL 5 . In my Linux Box i have two Lan cards (eth0 and eth1) . "eth0" is connected with network 192.168.10.0 and "eth1" is connected with network 192.168.11.0 . Both Network are inter connected via routing . Now I want a situation where , I want to dedicatedly... (2 Replies)
Discussion started by: shipon_97
2 Replies

5. UNIX for Dummies Questions & Answers

What would the physical address be for virtual address?

Hi guys, I got one problem which I definetily no idea. What would the physical address be for virtual address? 1) 2ABC 2) 3F4B Here is the page table:see attached Thank you sos sososososso much!! (0 Replies)
Discussion started by: lemon_06
0 Replies

6. UNIX for Dummies Questions & Answers

Removing IP address from eth1 on SUSE

Hello folks; I have a NIC card on my SUSE 10.3 server with eth0 & eth1 configured with two IP addresses (172.16.5.3 & 172.16.5.4) I'd like to remove the IP assigned to eth1 (172.16.5.4). i think i know i can go into ifcfg-eth1 and edit it but before i do that, i want to know if there's a better... (2 Replies)
Discussion started by: Katkota
2 Replies

7. IP Networking

Virtual Adapter MAC address..

Hi, I just want to know whether two MAC address can exist in a adapter.. I mean one there will be mandatory one And another as user defined one.. Any replies will be more helpful.. Please help.. :wall: (0 Replies)
Discussion started by: Priya Amaresh
0 Replies

8. IP Networking

IPv6 address block assign/associate with an interface

Hello all, I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack. One possible solution was to associate an IP block to an interface then bind to that... (6 Replies)
Discussion started by: redwil
6 Replies

9. UNIX for Advanced & Expert Users

C program to detect duplicate ip address if any after assigning ip address to ethernet interface

Hi , Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies

10. IP Networking

MAC Address - Four Interfaces with the same MAC Address

four interfaces with ifconfig all interfaces have the same mac. If is not set for unique. but it still works. what difference does it make to have all macs the same or different? (4 Replies)
Discussion started by: rrodgers
4 Replies
Match-all classifier in tc(8)					       Linux					     Match-all classifier in tc(8)

NAME
matchall - traffic control filter that matches every packet SYNOPSIS
tc filter ... matchall [ skip_sw | skip_hw ] [ action ACTION_SPEC ] [ classid CLASSID ] DESCRIPTION
The matchall filter allows to classify every packet that flows on the port and run a action on it. OPTIONS
action ACTION_SPEC Apply an action from the generic actions framework on matching packets. classid CLASSID Push matching packets into the class identified by CLASSID. skip_sw Do not process filter by software. If hardware has no offload support for this filter, or TC offload is not enabled for the inter- face, operation will fail. skip_hw Do not process filter by hardware. EXAMPLES
To create ingress mirroring from port eth1 to port eth2: tc qdisc add dev eth1 handle ffff: ingress tc filter add dev eth1 parent ffff: matchall skip_sw action mirred egress mirror dev eth2 The first command creats an ingress qdisc with handle ffff: on device eth1 where the second command attaches a matchall filters on it that mirrors the packets to device eth2. To create egress mirroring from port eth1 to port eth2: tc qdisc add dev eth1 handle 1: root prio tc filter add dev eth1 parent 1: matchall skip_sw action mirred egress mirror dev eth2 The first command creats an egress qdisc with handle 1: that replaces the root qdisc on device eth1 where the second command attaches a matchall filters on it that mirrors the packets to device eth2. To sample one of every 100 packets flowing into interface eth0 to psample group 12: tc qdisc add dev eth0 handle ffff: ingress tc filter add dev eth0 parent ffff: matchall action sample rate 100 group 12 SEE ALSO
tc(8), iproute2 21 Oct 2015 Match-all classifier in tc(8)
All times are GMT -4. The time now is 11:06 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy