12-07-2009
What is the exact model number of the Dell XPS?
What is the output of lspci?
9 More Discussions You Might Find Interesting
1. Solaris
hi experts,
i have some problem with my server v890, i had config the network with ce0,ce1 and eri0 but after reboot the server have this error messages display :
WARNING: ce0: fault detected external to device; service degraded
WARNING: ce0: xcvr addr:0x01 - link down
configuring IPv4... (2 Replies)
Discussion started by: bucci
2 Replies
2. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
3. Solaris
Dear All,
I am a beginner of Sun Solaris. Now I install Sun Solaris 10 on my machine Brand Dell optiplex 745. When i complete installation I found no Network Card
in my computer by using command ifconfig -a, I found only loopback Adapter.
Could anyone help me to solve this problem?
Cheer,
... (5 Replies)
Discussion started by: veasnabee
5 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
6. Linux
hello all,
how i can configure Squid with ONE Network Card for cache and proxy as shown in image attached. (1 Reply)
Discussion started by: jazaib92
1 Replies
7. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
8. Linux
i want to configure machine1 as ntp server. this machine has oel 5.9 64 bit installed and this machine is not connected to internet neither there is any ntp server.
there is another machine2 and i want to configure that as ntp client.
plz do tell me that what lines do i add in /etc/ntp.conf... (0 Replies)
Discussion started by: rehantayyab82
0 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT DEBIAN
xpstosvg
XPSTOSVG(1) XPS Tools XPSTOSVG(1)
NAME
xpstosvg - XPS to SVG converter
SYNOPSIS
xpstosvg [OPTION...] FILE [OUTPUT FILE]
DESCRIPTION
xpstosvg converts XPS documents to SVG format. xpstosvg reads the XPS file, FILE, and writes a SVG file, OUTPUT FILE. If OUTPUT FILE is
not specified the output filename will be derived from the OUTPUT FILE filename.
OPTIONS
-?, --help
Show help options.
-d DOCUMENT, --document=DOCUMENT
The document inside the XPS file to convert. By default, the first document of the XPS file is used.
-f PAGE, --first=PAGE
The first page to convert.
-l PAGE, --last=PAGE
The last page to convert.
-o, --odd
Convert only odd pages.
-e, --even
Convert only even pages.
-r RESOLUTION, --resolution=RESOLUTION
Horizontal and vertical resolution in PPI (Pixels Per Inch). The default is 150 PPI.
--rx=RESOLUTION
Horizontal resolution in PPI (Pixels Per Inch). The default is 150 PPI.
--ry=RESOLUTION
Vertical resolution in PPI (Pixels Per Inch). The default is 150 PPI.
-x X, --crop-x=X
The x-coordinate of the crop area top left corner.
-y Y, --crop-y=Y
The y-coordinate of the crop area top left corner.
-w WIDTH, --crop-width=WIDTH
The width of crop area.
-h HEIGHT, --crop-height=HEIGHT
The height of crop area.
--paper-width=WIDTH
The paper width.
--paper-height=HEIGHT
The paper height.
--expand
Expand pages smaller than the paper to fill the paper. By default, pages are not scaled.
--no-shrink
Don't scale pages which are larger than the paper. By default, pages larger than the paper are shrunk to fit.
--no-center
Don't center on the paper pages smaller than the paper (after any scaling). By default, pages smaller than the paper are aligned to the
lower-left corner.
BUGS
Please send bug reports to https://bugzilla.gnome.org/enter_bug.cgi?product=libgxps.
SEE ALSO
xpstojpeg(1) xpstopng(1) xpstopdf(1) xpstops(1)
XPS Tools 11/19/2011 XPSTOSVG(1)