12-07-2009
How to configure network interface card in OEL.
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur
9 More Discussions You Might Find Interesting
1. Solaris
hi experts,
i have some problem with my server v890, i had config the network with ce0,ce1 and eri0 but after reboot the server have this error messages display :
WARNING: ce0: fault detected external to device; service degraded
WARNING: ce0: xcvr addr:0x01 - link down
configuring IPv4... (2 Replies)
Discussion started by: bucci
2 Replies
2. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
3. Solaris
Dear All,
I am a beginner of Sun Solaris. Now I install Sun Solaris 10 on my machine Brand Dell optiplex 745. When i complete installation I found no Network Card
in my computer by using command ifconfig -a, I found only loopback Adapter.
Could anyone help me to solve this problem?
Cheer,
... (5 Replies)
Discussion started by: veasnabee
5 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
6. Linux
hello all,
how i can configure Squid with ONE Network Card for cache and proxy as shown in image attached. (1 Reply)
Discussion started by: jazaib92
1 Replies
7. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
8. Linux
i want to configure machine1 as ntp server. this machine has oel 5.9 64 bit installed and this machine is not connected to internet neither there is any ntp server.
there is another machine2 and i want to configure that as ntp client.
plz do tell me that what lines do i add in /etc/ntp.conf... (0 Replies)
Discussion started by: rehantayyab82
0 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies