1) AIX Supports iSCSI. If FreeNAS utilizes the iSCSI protocol, than it can be used.
2) see first answer
3) check your system to see if the iscsi drivers are installed, if they are not you can install them from CD or download them from IBM's website.
I have a standard template I deploy for each of my AIX servers. It's in a mksysb format which I pulled via the nim server after I originally set it up.
I'm trying to restore this mksysb over the wire to a remote system. The remote system is an lpar running under vio (no HMC attached). The disk... (1 Reply)
Can you have a Dynamic LPAR without VIO and if yes is there a benefit to having both? I am attempting to implement VIO and Resource pooling at my company and want to understand the limitations.
Also, I have been told the managing and allocation of the Logical Volumes is a time consuming task as... (0 Replies)
We have a frame the uses 2 vios that assign disk storage to LPAR's. We have a LPAr with multiple disk and I want to know how do I tell which vio is serving the disk. For example the LPAr has hdisk 0, 1, 2, 3 all the same size. I want to know which vio is serving hdisk0, 1. (4 Replies)
VIO Server is managing both AIX Clients and Linux Clients. For AIX Clients, we could do a disk mapping from slot numbers to VIO and also uname -L to determine the lparid and serial number frame its running on.
From a Linux Client,
How do I know which IBM frame its running on? Any command to... (4 Replies)
I am wondering if there is a command I can run from **with-in** LPAR server (server01) to find out the hostname or IP address or other parameters for VIO server in charge of server01? (1 Reply)
Just a question which may seem dumb to some out there, but then again I am not a super technie so that's my excuse.
Is it possible to say provision a test AIX LPAR (has a 10gb boot lun and 20gb data) under a VIO which has connectivity to SAN Array A so it can see the disks provisioned to it,... (2 Replies)
Previous forum threads have noted that AIX cannot use iSCSI disks because it fails when trying to add them to a volume group using mkvg. The failure is caused by AIX's use of the SCSI "WRITE AND VERIFY"(0x2e) command which some iSCSI targets do not support.
We experienced the same problem using... (1 Reply)
Hi All,
I've been trying to create a new LPAR for some days now but I can't get the VIO server to recognize the new LPAR. This is what I did:
On HMC create new LPAR
On HMC create new virtual scsi adapter for LPAR in VIO profile
On HMC add new virtual scsi adapter for LPAR with DLPAR... (6 Replies)
I am using Windows Server 2008R2 as a domain controller to 2 other servers and would like to use my Dell Powervault 770N as my NAS for data storage. I have FC that I would like to implement between the servers and the NAS (as an iSCSI target). I am brand new to this world; is this possible? I am... (2 Replies)
:wall::wall::wall:
1. I have created an LPAR in the HMC.
2. I have allocated the storage from an Hitachi AMS2500 and assigned it to the host group.
3. I have zoned the LPAR and Storage on a Brocade 5100. (The zone sees the AMS)
Next I activated the LPAR in the HMC, SMS mode for the mksysb... (3 Replies)
Discussion started by: Dallasguy7
3 Replies
LEARN ABOUT CENTOS
radwho
RADWHO(1) FreeRADIUS Daemon RADWHO(1)NAME
radwho - show online users
SYNOPSIS
radwho [-c] [-d raddb_directory] [-F radutmp_file] [-i] [-n] [-N nas_ip_address] [-p] [-P nas_port] [-r] [-R] [-s] [-S] [-u user] [-U user]
[-Z]
DESCRIPTION
The FreeRADIUS server can be configured to maintain an active session database in a file called radutmp. This utility shows the content of
that session database.
OPTIONS -c Shows caller ID (if available) instead of the full name.
-d raddb_directory
The directory that contains the RADIUS configuration files. Defaults to /etc/raddb.
-F radutmp_file
The file that contains the radutmp file. If this is specified, -d is not necessary.
-i Shows the session ID instead of the full name.
-n Normally radwho looks up the username in the systems password file, and shows the full username as well. The -n flags prevents this.
-N nas_ip_address
Show only those entries which match the given NAS IP address.
-p Adds an extra column for the port type - I for ISDN, A for Analog.
-P nas_port
Show only those entries which match the given NAS port.
-r Outputs all data in raw format - no headers, no formatting, fields are comma-separated.
-R Output all data in RADIUS attribute format. All fields are printed.
-s Show full name.
-S Hide shell users. Doesn't show the entries for users that do not have a SLIP or PPP session.
-u user
Show only those entries which match the given username (case insensitive).
-U user
Show only those entries which match the given username (case sensitive).
-Z When combined with -R, prints out the contents of an Accounting-Request packet which can be passed to radclient, in order to "zap"
that users session from radutmp.
For example,
$ radwho -ZRN 10.0.0.1 | radclient -f - radius.example.net acct testing123
will result in all an Accounting-Request packet being sent to the RADIUS server, which tells the server that the NAS rebooted. i.e. It
"zaps" all of the users on that NAS.
To "zap" one user, specifiy NAS, username, and NAS port:
$ radwho -ZRN 10.0.0.1 -u user -P 10 | radclient -f - radius.example.net acct testing123
Other combinations are also possible.
SEE ALSO radiusd(8), radclient(1), radiusd.conf(5).
AUTHOR
Miquel van Smoorenburg, miquels@cistron.nl.
17 Feb 2013 RADWHO(1)