|
|
Sponsored Content
Operating Systems
Solaris
Link aggregation
Post 302376861 by PatrickBaer on Wednesday 2nd of December 2009 01:19:11 PM
12-02-2009
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. Solaris
Hi everybody,
One client asked me to configure network failover and load balancing for two Ethernet interfaces, I tried IPMP but I was unable to do so, because he's using his Gateway as firewall and PING is disabled.
so IPMP kept telling me that all interfaces failed because gateway can't be... (8 Replies)
Discussion started by: Sun Fire
8 Replies
4. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
5. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
6. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
7. HP-UX
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Discussion started by: mkiron
1 Replies
8. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
9. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
10. Solaris
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
LEARN ABOUT DEBIAN
aoe-interfaces
aoe-interfaces(8) System Manager's Manual aoe-interfaces(8) NAME
aoe-interfaces - restrict aoe driver to specified network interfaces SYNOPSIS
aoe-interfaces [dev1] [dev2 ...] aoe-interfaces -c DESCRIPTION
The aoe-interfaces command tells the aoe driver to ignore ATA over Ethernet (AoE) traffic on all but the specified network interfaces. It is analogous to the aoe_iflist module load option. If neither the aoe_iflist module load option nor the aoe-interfaces command are used, the aoe driver will use any network interface for AoE traffic. Using aoe-interfaces to limit AoE to only trusted networks prevents the case where a rogue AoE target appears on a public net- work, diverting data from the legitimate AoE target. Such an imposter target effectively corrupts the data on the legitimate target. If the aoe driver is a module, then calling aoe-interfaces without arguments will display the current interfaces list. If it hasn't been set then the output will be blank. It's good to run the aoe-discover command after setting the AoE interfaces list. OPTIONS
-c The -c flag will clear the interface access list, permitting any interface to be used. EXAMPLE
In this example, the root user on a host named nai loads the aoe module with only eth0 allowable for AoE traffic. After remembering that shelf 7 is on eth3, this sysadmin uses aoe-interfaces to add eth3 to the list of allowable network interfaces and then calls aoe-discover to ask the aoe driver to look for new AoE devices. nai:~# modprobe aoe aoe_iflist="eth0" nai:~# aoe-stat e10.9 eth0 up nai:~# aoe-interfaces eth0 eth3 nai:~# aoe-discover nai:~# aoe-stat e7.0 eth3 up e7.1 eth3 up e7.2 eth3 up e7.3 eth3 up e7.4 eth3 up e7.5 eth3 up e7.6 eth3 up e7.7 eth3 up e7.8 eth3 up e7.9 eth3 up e10.9 eth0 up nai:~# aoe-interfaces eth0 eth3 SEE ALSO
aoe-discover(8), aoe-stat(8), aoetools(8). AUTHOR
Ed L. Cashin (ecashin@coraid.com) aoe-interfaces(8)