Sponsored Content
Full Discussion: Link aggregation
Operating Systems Solaris Link aggregation Post 302376861 by PatrickBaer on Wednesday 2nd of December 2009 01:19:11 PM
Old 12-02-2009
ok ok, I probably haven't expressed it clearly enough:

I have set up two interfaces with link aggregation and they work just fine!

But: When I start an rsync process or scp or whatever similar, it only uses one physical interface. So what I am looking for is a way, to distribute traffic from a single process, e.g. rsync, to both interfaces.
 

10 More Discussions You Might Find Interesting

1. Solaris

Link Aggregation

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies

2. UNIX for Advanced & Expert Users

Link Aggregation and LACP

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

3. Solaris

Difference between IPMP and Link Aggregation ?

Hi everybody, One client asked me to configure network failover and load balancing for two Ethernet interfaces, I tried IPMP but I was unable to do so, because he's using his Gateway as firewall and PING is disabled. so IPMP kept telling me that all interfaces failed because gateway can't be... (8 Replies)
Discussion started by: Sun Fire
8 Replies

4. IP Networking

bonding without switch link aggregation

I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies

5. AIX

Link aggregation with hacmp ?

Hi, I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies

6. HP-UX

Link Aggregation HPUX

Hi, Hoping someone can offer some advice on something i have not dealt with before. We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies

7. HP-UX

Break Link Aggregation in HP UX.

Hi, I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900. Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server. So It need to change in cluster script. But I dont know where I have to change it. Please... (1 Reply)
Discussion started by: mkiron
1 Replies

8. Solaris

Link Aggregation without LACP

Hi, I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP? I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies

9. IP Networking

Link Aggregation

Hi ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ? are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies

10. Solaris

How can I test link aggregation?

Hi, I have Solaris-10 server and link aggregation is configured on this in below way # dladm show-aggr key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto) device address speed duplex link state bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
OCF_HEARTBEAT_RSYNCD(7) 					OCF resource agents					   OCF_HEARTBEAT_RSYNCD(7)

NAME
ocf_heartbeat_rsyncd - Manages an rsync daemon SYNOPSIS
rsyncd [start | stop | monitor | meta-data | validate-all] DESCRIPTION
This script manages rsync daemon SUPPORTED PARAMETERS
binpath The rsync binary path. For example, "/usr/bin/rsync" (optional, string, default rsync) conffile The rsync daemon configuration file name with full path. For example, "/etc/rsyncd.conf" (optional, string, default /etc/rsyncd.conf) bwlimit This option allows you to specify a maximum transfer rate in kilobytes per second. This option is most effective when using rsync with large files (several megabytes and up). Due to the nature of rsync transfers, blocks of data are sent, then if rsync determines the transfer was too fast, it will wait before sending the next data block. The result is an average transfer rate equaling the specified limit. A value of zero specifies no limit. (optional, string, no default) SUPPORTED ACTIONS
This resource agent supports the following actions (operations): start Starts the resource. Suggested minimum timeout: 20s. stop Stops the resource. Suggested minimum timeout: 20s. monitor Performs a detailed status check. Suggested minimum timeout: 20s. Suggested interval: 60s. validate-all Performs a validation of the resource configuration. Suggested minimum timeout: 20s. meta-data Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5s. EXAMPLE
The following is an example configuration for a rsyncd resource using the crm(8) shell: primitive p_rsyncd ocf:heartbeat:rsyncd op monitor depth="0" timeout="20s" interval="60s" SEE ALSO
http://www.linux-ha.org/wiki/rsyncd_(resource_agent) AUTHOR
Linux-HA contributors (see the resource agent source for information about individual authors) resource-agents UNKNOWN 03/09/2014 OCF_HEARTBEAT_RSYNCD(7)
All times are GMT -4. The time now is 03:56 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy