Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Link aggregation
Operating Systems Solaris Link aggregation Post 302376861 by PatrickBaer on Wednesday 2nd of December 2009 01:19:11 PM
Old 12-02-2009
ok ok, I probably haven't expressed it clearly enough:

I have set up two interfaces with link aggregation and they work just fine!

But: When I start an rsync process or scp or whatever similar, it only uses one physical interface. So what I am looking for is a way, to distribute traffic from a single process, e.g. rsync, to both interfaces.
 

10 More Discussions You Might Find Interesting

1. Solaris

Link Aggregation

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies

2. UNIX for Advanced & Expert Users

Link Aggregation and LACP

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

3. Solaris

Difference between IPMP and Link Aggregation ?

Hi everybody, One client asked me to configure network failover and load balancing for two Ethernet interfaces, I tried IPMP but I was unable to do so, because he's using his Gateway as firewall and PING is disabled. so IPMP kept telling me that all interfaces failed because gateway can't be... (8 Replies)
Discussion started by: Sun Fire
8 Replies

4. IP Networking

bonding without switch link aggregation

I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies

5. AIX

Link aggregation with hacmp ?

Hi, I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies

6. HP-UX

Link Aggregation HPUX

Hi, Hoping someone can offer some advice on something i have not dealt with before. We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies

7. HP-UX

Break Link Aggregation in HP UX.

Hi, I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900. Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server. So It need to change in cluster script. But I dont know where I have to change it. Please... (1 Reply)
Discussion started by: mkiron
1 Replies

8. Solaris

Link Aggregation without LACP

Hi, I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP? I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies

9. IP Networking

Link Aggregation

Hi ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ? are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies

10. Solaris

How can I test link aggregation?

Hi, I have Solaris-10 server and link aggregation is configured on this in below way # dladm show-aggr key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto) device address speed duplex link state bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies

LEARN ABOUT CENTOS

pmdabonding

PMDABONDING(1)						       Performance Co-Pilot						    PMDABONDING(1)

NAME

       pmdabonding - Linux bonded interface performance metrics domain agent (PMDA)

DESCRIPTION

       pmdabonding is a Performance Metrics Domain Agent (PMDA) which exports metric values from bonded network interfaces in the Linux kernel.

INSTALLATION

       If you want access to the names and values for the bonding performance metrics, do the following as root:

	       # cd $PCP_PMDAS_DIR/bonding
	       # ./Install

       If you want to undo the installation, do the following as root:

	       # cd $PCP_PMDAS_DIR/bonding
	       # ./Remove

       pmdabonding is launched by pmcd(1) and should never be executed directly.  The Install and Remove scripts notify pmcd(1) when the agent is
       installed or removed.

FILES

       $PCP_PMDAS_DIR/bonding/Install
	   installation script for the pmdabonding agent

       $PCP_PMDAS_DIR/bonding/Remove
	   undo installation script for the pmdabonding agent

       $PCP_LOG_DIR/pmcd/bonding.log
	   default log file for error messages from pmdabonding

SEE ALSO

       pmcd(1) and ifenslave(8).

3.8.10							       Performance Co-Pilot						    PMDABONDING(1)
All times are GMT -4. The time now is 08:38 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy