11-24-2009
"If the tape is configured as 2, and the device is set to 3, then nothing will show in the messages file."
ahh...thanks
Would dcu (device configuration utililty) tell me the actual hardware jumper settings or would it also give the silent treatment if /etc/conf/cf.d/mscsi did not match actual jumper settings?
Isn't ps -A the command for all process on SCO? I didn't see NFS or Samba running, but I didn't know about VisionFS.
8 More Discussions You Might Find Interesting
1. Linux Benchmarks
Notes:
System Configuration: Dell Computer Corporation PowerEdge 4600 (4 X Intel(R) XEON(TM) CPU 2.00GHz
1988.782 MHz) hyperthreaded
System clock frequency: 99.0827 MHz
Memory size (approximate): 2559 Megabytes
========================= CPUs ========================
CPU # CPU... (0 Replies)
Discussion started by: tnorth
0 Replies
2. Linux Benchmarks
CPU/Speed: Dual PIII 533
Ram: 256Mb PC133
Motherboard: Unknown, Intel Chipset
Cache: 256k on board
Controller: PARC Raid 2/Si, AIC-7880U
Disk: 30Gb RAID 5
Load: 1 user. Clean boot, init 5 but X-Windows not loaded.
Kernel: See Benchmarks.
pgms: gcc 3.2.3
... (2 Replies)
Discussion started by: Garp
2 Replies
3. Solaris
hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request...
the installation crashes when trying to detect the NICS... (0 Replies)
Discussion started by: xinugeek
0 Replies
4. Red Hat
I have successfully installed RedHat 8.0 onto a Dell PowerEdge SC1425 today. This server has two SATA hard drives, and an IDE DVD-ROM drive.
Using the following kernel parameters, i successfully installed across both hard drives from CD:
ide0=0x1f0,0x3f6,14 vga=791 resolution=1024x768 expert... (5 Replies)
Discussion started by: fishsponge
5 Replies
5. Filesystems, Disks and Memory
Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,... (1 Reply)
Discussion started by: Fatflea
1 Replies
6. UNIX for Dummies Questions & Answers
I have 2 Dell Poweredge 1950 servers running . I have been having intermittent performance issues with the NIC cards on one of them. The two servers are identical and are running the same operating system. The server that has the issue is on the DMZ on a a static IP and is hosting a website. ... (0 Replies)
Discussion started by: skotapal
0 Replies
7. SCO
Hello all,
I'am experiencing weird relyability problems with a SCO 6.0 Openserver server that runs on a Dell Poweredge 1800 equipped with a PERC DC4 raid controller and 4 36 GB 15 K rpm hot swappable scsi harddisks.
It runs a RAID 10 configuration.
It uses the mega hba, Revision 8.03a Release... (1 Reply)
Discussion started by: frederik1
1 Replies
8. Programming
Hi,
I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines.
I receive a 'EFAULT' when I try to access /dev/mem on these servers.
I suspect some... (1 Reply)
Discussion started by: ragisreekanth
1 Replies
LEARN ABOUT REDHAT
amverify
AMVERIFY(8) System Manager's Manual AMVERIFY(8)
NAME
amverify - check an Amanda tape for errors
SYNOPSIS
amverify config [ slot [ runtapes ] ]
DESCRIPTION
Amverify reads an Amanda format tape and makes sure each backup image can be processed by amrestore and, if possible, the appropriate
restore program (e.g. tar).
Amverify runs amrestore on each file of the tape and pipes the output to a restore program (if available) with an option to create a cata-
logue of the backup. The catalogue itself is discarded. Only the success or failure of the operation itself is reported.
If the backup image cannot be processed by the restore program, e.g. if it was written on a different operating system, the image is sent
through dd to /dev/null. This still determines if the tape is readable, but does not do any internal consistency check on the image.
If config is set up to use a tape changer, the slot argument may be used to choose the first tape to process. Otherwise, the current slot
is used.
The runtapes configuration parameter determines how many tapes are processed unless it is specified on the command line.
See the amanda(8) man page for more details about Amanda.
AUTHOR
Axel Zinser <fifi@icem.de>
SEE ALSO
amrestore(8), amanda(8), amverifyrun(8)
AMVERIFY(8)