Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
LEARN ABOUT DEBIAN
aggregate-ios
AGGREGATE-IOS(1) General Commands Manual AGGREGATE-IOS(1)NAME
aggregate-ios - optimise a concatenated set of cisco/IOS prefix filters to help make them nice and short.
SYNOPSIS
aggregate-ios <source_config >optimised_config
DESCRIPTION
Takes cisco IOS configuration on stdin, and optimises any prefix filters found using aggregate(1). Optimised filters are produced on std-
out.
OPTIONS
None.
DIAGNOSTICS
Any diagnostics produced by aggregate(1) are passed through on stderr.
EXAMPLES
The following configuration fragment:
ip prefix-list AS65530 description Foo, Inc
ip prefix-list AS65530 permit 10.1.0.0/16
ip prefix-list AS65530 permit 10.2.0.0/16
ip prefix-list AS65530 permit 10.2.1.0/24
ip prefix-list AS65530 permit 10.3.0.0/16
ip prefix-list AS65531 description Bar.Com
ip prefix-list AS65531 seq 5 permit 192.168.1.0/24
ip prefix-list AS65531 seq 10 permit 192.168.2.0/24
ip prefix-list AS65531 seq 15 permit 192.168.0.0/19
is optimised as follows:
ip prefix-list AS65530 permit 10.1.0.0/16 le 24
ip prefix-list AS65530 permit 10.2.0.0/15 le 24
ip prefix-list AS65531 permit 192.168.0.0/19 le 24
SEE ALSO aggregate(1)HISTORY
Aggregate-ios was written by Joe Abley <jabley@mfnx.net>.
BUGS
All those in aggregate(1) and then some :)
Joe Abley 2000 November 27 AGGREGATE-IOS(1)