11-24-2009
thankyou vbe!
i have a question about why I checked LUNs status after replaced that all luns only run on the controller A,no LUN runs on the controller B.
Can FC60 transfer LUNs to a normal controller when detected another controller failed or not normal itself.
Thank you!
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
2. Shell Programming and Scripting
hi
I get test: unknown operator status
if
then
echo "OK."
return 0
else
echo "not ok" 2>&1
exit -1
fi
I tried to change "A" with 'A' --> same error
I tried to change
if , I am getting: (3 Replies)
Discussion started by: melanie_pfefer
3 Replies
3. SCO
hi...
i hav a problem to install sco unix
while installing sco unix 5.0.5 in acer altos with hardware raid
am getting error
"Warning HD: no root disk controller was found
system error 5: while getting fs type
flushing controller: DAC960PRL cache done."
i hav use the following... (18 Replies)
Discussion started by: mselvaprakash
18 Replies
4. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
5. Solaris
hi all
i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output
# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies
6. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
7. Solaris
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Discussion started by: kebabbert
2 Replies
8. Solaris
Can someone point me to a procedure detailing the replacement of a failed battery in a SUN 6540 controller.
Or describe the procedure.
Thanks (1 Reply)
Discussion started by: USFE
1 Replies
9. Solaris
Hi
The scenario in the oracle t4-1 hardware with solaris 10 is as follows:
1. The initial install on the server was performed with an incorrect disk layout.
2. New disks were ordered and slot into the server.
3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies
10. Filesystems, Disks and Memory
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (1 Reply)
Discussion started by: terrya
1 Replies
LEARN ABOUT OSF1
do_config
do_config(9r) do_config(9r)
NAME
do_config - EISA/ISA: Initializes the device to its assigned configuration
SYNOPSIS
void do_config(
struct controller *ctlr_p );
ARGUMENTS
Specifies a pointer to the controller structure associated with the controller to be configured. The do_config routine obtains the device
to initialize through its controller's associated controller structure pointer.
DESCRIPTION
The do_config routine initializes the specified controller based on its power-up resource assignments. If the device uses either an inter-
rupt or a DMA channel, then do_config also performs any setup requirements. For example, for controllers that connect to the EISA bus,
do_config initializes the controller according to the parameters specified in the EISA configuration file.
NOTES
The do_config routine is a generic interface that maps to a bus-specific interface that actually initializes the specified device. Using
this routine to initialize a device makes the driver more portable across different bus architectures. Not all buses support the do_config
routine.
RETURN VALUES
None
SEE ALSO
Routines: get_config(9r), get_info(9r)
Data Structures: controller(9s)
do_config(9r)