11-18-2009
Temporarily disabling unused ethernet adapter
Hi,
In our AIX 5.2 server , we have one unused ethernet adapter which doesn't have cable connection . For this interface , we are getting alerts in errpt .
Could you suggesthow to stop this alert ? And sametime i would like to keep this device in ODM .
Is there anyway to change the state of device from "Available" to "Stopped" ?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies
2. Solaris
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Discussion started by: tubbyrana
2 Replies
3. Solaris
hi all,
How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies
4. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
5. Red Hat
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies
6. AIX
Good morning,
Saw this on a system this morning, thought I'd check with this group before calling IBM.
Basically what we have here is a P7 running 6.1 reporting the following in errpt:
LABEL: GOENT_LINK_DOWN
IDENTIFIER: EC0BCCD4
This is for ent4, which is odd because we... (0 Replies)
Discussion started by: Michael Mullig
0 Replies
7. Hardware
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Discussion started by: Lhao
5 Replies
8. AIX
Hi Techies,
I have a doubt.
ent0 Available Logical Host Ethernet Port (lp-hea)
ent1 Available Logical Host Ethernet Port (lp-hea)
ent2 Available Logical Host Ethernet Port (lp-hea)
ent3 Available Logical Host Ethernet Port (lp-hea)
ent4 Available... (4 Replies)
Discussion started by: jayadeava
4 Replies
9. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
10. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
LEARN ABOUT OPENSOLARIS
scconf_transp_adap_ge
scconf_transp_adap_ge(1M) System Administration Commands scconf_transp_adap_ge(1M)
NAME
scconf_transp_adap_ge - configure the Gigabit Ethernet (ge) transport adapter
DESCRIPTION
Note -
Beginning with the Sun Cluster 3.2 release, Sun Cluster software includes an object-oriented command set. Although Sun Cluster software
still supports the original command set, Sun Cluster procedural documentation uses only the object-oriented command set. For more infor-
mation about the object-oriented command set, see the Intro(1CL) man page.
You can configure ge adapters as cluster transport adapters. These adapters can only be used with transport type dlpi.
The ge adapter connects to a transport switch or to another ge adapter on a different node. In either case, the connection is made through
a transport cable.
When a transport switch is used and the endpoints of the transport cable are configured using scconf, scinstall, or other tools, you are
asked to specify a port name on the transport switch. You can provide any port name, or accept the default, as long as the name is unique
for the switch.
The default is to set the port name to the node ID hosting the adapter at the other end of the cable.
There are no user configurable properties for cluster transport adapters of this type.
SEE ALSO
clinterconnect(1CL), clnode(1CL), scconf(1M), scinstall(1M), ge(7D)
Sun Cluster 3.2 4 May 2006 scconf_transp_adap_ge(1M)