I think I did it wrong, again. Here were the results:

What is the LUN of this device?
Press <Return> to use the default: 0
Select 0-7, or h for help, or q to quit: 0

You are about to add the following SCSI device:

Host
Adapter Adapter
Type Device Number ID LUN BUS
----------------------------------------------
mdac Sdsk 0 1 0 1

Update SCSI configuration? (y/n) y

The SCSI configuration file has been updated.
\nA new kernel must be built and rebooted before disk configuration can continue
. Would you like to relink at this time? (y/n) \c
y

The UNIX Operating System will now be rebuilt.
This will take a few minutes. Please wait.

Root for this system build is /
idmkreg: can not locate or open 'Sdsk/device.dat'

*
wd Srom 1 0 0 0
mdac Sdsk 0 0 1 0

alad Stp 0 2 0 0


mdac Sdsk 0 1 1 0

mdac Sdsk 0 1 0 1
bash-2.03#

---------- Post updated at 09:03 AM ---------- Previous update was at 08:45 AM ----------

deleted the one in red & rebuilt the kernel.....tried this.....but this is pointing to a specific disk (in red)??

Enter the prefix of the SCSI host adapter that supports this device
or press <Return> for the default: 'mdac'
Enter h for a list of host adapters or enter q to quit:

Which 'mdac' SCSI host adapter supports this device?
Select 0-4, or enter q to quit: 0

The Host Adapter parameters will be automatically configured

What SCSI Bus is this device attached to?
Press <Return> to use the default:0
Select 0-n, or h for help, or q to quit: 0

What is the Target ID for this device?
Select 0-15, or h for help, or q to quit: 1

What is the LUN of this device?
Press <Return> to use the default: 0
Select 0-7, or h for help, or q to quit: 1
\nDisk already configured as disk number 1 (/dev/dsk/1s0)
\nDuring installation you may choose to overwrite all
or part of the present contents of your hard disk.
\nDo you wish to continue? (y/n) \c

---------- Post updated at 09:15 AM ---------- Previous update was at 09:03 AM ----------

I don't know if this is the right one? Would this be my new 17GB hard drive that I need?? Appreciate more. Thanks.

bash-2.03# divvy /dev/hd3a
+-------------------+------------+--------+---+-------------+------------+
| Name | Type | New FS | # | First Block | Last Block |
+-------------------+------------+--------+---+-------------+------------+
| | HTFS | no | 0 | 0| 15997967|
| | NOT USED | no | 1 | -| -|
| | NOT USED | no | 2 | -| -|
| | NOT USED | no | 3 | -| -|
| | NOT USED | no | 4 | -| -|
| | NOT USED | no | 5 | -| -|
| | NOT USED | no | 6 | -| -|
| hd3a | WHOLE DISK | no | 7 | 0| 15999999|
+-------------------+------------+--------+---+-------------+------------+
15997968 1K blocks for divisions, 2032 1K blocks reserved for the system

n[ame] Name or rename a division.
c[reate] Create a new file system on this division.
t[ype] Select or change filesystem type on new filesystems.
p[revent] Prevent a new file system from being created on this division.
s[tart] Start a division on a different block.
e[nd] End a division on a different block.
r[estore] Restore the original division table.

Enter your choice or q to quit: