I have my SC setup as attached below but I am having problem accessing the port thru network. sc0 was accessible only after i failed over the configuratios to sc1 (now then sc1 was not pingable ). Just wondering is there anything wrong with my sc settings? Appreciate your advice.
Network settings: 10Mpbs/Half Duplex
Code:
The system controller is configured to be on a network.
Network settings: static
Hostname: sc0
IP Address: 128.230.31.149
Netmask: 255.255.255.0
Gateway: 128.230.31.1
DNS Domain:
Primary DNS Server:
Secondary DNS Server:
Connection type: telnet
Idle connection timeout : No timeout
Loghost for Platform: 10.0.0.1
Log Facility for Platform: local0
SNTP server: 0.0.0.0
SNMP Agent: disabled
Chassis Description: Sun Fire 4800
Chassis Contact: adminstrator
Chassis Location: 10F IT Dept
ACL for Domain A: SB0 SB2 SB4 IB6 IB8
ACL for Domain B: SB0 SB2 SB4 IB6 IB8
ACL for Domain C: SB0 SB2 SB4 IB6 IB8
ACL for Domain D: SB0 SB2 SB4 IB6 IB8
Chassis HostID: 83041764
PROC RTUs installed: 0
PROC Headroom Quantity: 0
PROC RTUs reserved for domain A: 0
PROC RTUs reserved for domain B: 0
PROC RTUs reserved for domain C: 0
PROC RTUs reserved for domain D: 0
SC POST diag Level: min
SC Failover: enabled and active.
Logical Hostname: 10.0.0.4
Chassis is in single partition mode.
UltraSPARC IV+ is not supported in domain A
Frame information is not available.
Hello guys,
I've recentrly installed a Tomcat server in our Solaris 8 servers, and while it's properly configured and running already, I can't access the port from outside the network segment the server is on.
I.e., we have 4 servers in the same segment (consecutive IP addresses), and if I... (4 Replies)
I wrote a small fortran program that I want to control with a bash script. The bash script builds a parameter file that is used by the fortran program. I want to make it so I can access the script from any directory on my computer. How do I do that? Or what key words should I search for to find... (1 Reply)
Hi everybody
I am facing a little problem with names servers. I have a VPS with Kloxo installed on it
I have registered 2 name servers (i.e. ns1.domain.com and ns2.domain.com) past one month.
These nameservers are not accessible yet. I have check the nameserver on internic site and they are... (3 Replies)
Hello everyone,
I am using centOS 5.4. and in the Graphical environment when i executed command system-config-kickstart , at the same time i lost my graphical environment now i am not able to access it, but i can access my system by CLI mode....kindly suggest me that how can i repare my... (3 Replies)
Hello.
What's the best way to ensure that a NFS filesystem mounted from a disk-cabine (NAS) is accessible?
My proposal:
1. ping to the ip of the cabine
2. verify filesystem is mounted
3. touch a file inside the /mountpoint
Any other suggestions?
Thank you! (2 Replies)
Hi techies
I am trying to write a script which can give me a ATP of a job,
My idea is :
store a value in a temp variable, next script read the variable in next call of it and give me the diff of values which is ATP, as script is running every hours.
Can we do this in Shell Script.
If... (5 Replies)
I am using ubuntu 12.04.03. I have some basic experience with webpy and I had it working for my LAN just by following the tutorial. The framework needs to be able to be used from outside the local network. I have difficulty seeing how to make the framework accessible from outside the lan. I tried... (10 Replies)
Hey everyone,
Just a random question, is it possible to have a publically accessible website without a domain name attached to it? That is if I assign the server an IP address and have apache listen on 80 for incoming requests, can someone type that IP address into their browser and get to the... (2 Replies)
Discussion started by: Lost in Cyberia
2 Replies
LEARN ABOUT OPENSOLARIS
network-admin
network-admin(1) User Commands network-admin(1)NAME
network-admin - Basic administration of network interfaces.
SYNOPSIS
network-admin [--configure=INTERFACE] [--configure-type=TYPE] [gnome-std-options]
DESCRIPTION
network-admin enumerates the interfaces available to the user and provides a mechanism for configuring these interfaces as static-IP or
DHCP. It's also possible to select which interfaces should be enabled on boot.
network-admin also allows you configure the systems hostname, DNS options and hosts using the user interface.
OPTIONS
The following options are supported:
-c, --configure=INTERFACE Configure a specific network interface (e.g. ath0 or bge0).
-t, --configure-type=TYPE Configure the first network interface of a specific type (e.g. ethernet or wireless).
gnome-std-options Standard options available for use with most GNOME applications. See gnome-std-options(5) for more informa-
tion.
EXAMPLES
Example 1: Running the main application.
example% network-admin
Example 2: Configuring the ath0 network interface.
example% network-admin --configure=ath0
Example 3: Configuring the first ethernet interface.
example% network-admin --configure-type=ethernet
EXIT STATUS
The following exit values are returned:
0 Application exited successfully
>0 Application exited with failure
FILES
The following files are used by this application:
/usr/bin/network-admin Executable for network interface configuration.
/etc/inet/gnome-system-tools Storage location for network configuration files when not active on boot.
/var/spool/setup-tool-backends/backup/network
Backup directory for files that are modified.
/var/spool/setup-tool-backends/data/network
Where "Location" profiles are stored.
/var/run/setup-tool-backends/debug/network
Debug logs can be found under here.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWgnome-system-tools |
+-----------------------------+-----------------------------+
|Interface stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO
Latest version of the GNOME Desktop User Guide for your platform.
users-admin(1), shares-admin(1), services-admin(1), time-admin(1), gnome-std-options(5), ifconfig(1M), hosts(4), nsswitch.conf(4),
resolv.conf(4), attributes(5)NOTES
This tool can only be used to manage physical network devices as returned by the "dladm show-dev" command, it does not support configura-
tion of more complex configurations.
There is currently no support for enterprise name services such as YP/NIS, NIS+ or LDAP. There is also no support for anything but the
global zone.
Written by Darren Kenny, Sun Microsystems Inc., 2006.
SunOS 5.11 6 Nov 2006 network-admin(1)
10-27-2009
). Just wondering is there anything wrong with my sc settings? Appreciate your advice.