Sponsored Content
Full Discussion: Network cards - Routing
Operating Systems Solaris Network cards - Routing Post 302363839 by incredible on Wednesday 21st of October 2009 12:11:53 PM
Old 10-21-2009
You ARE using the qfe for your route, isn't it so??
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

SCO Unix and Two Network Cards

Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies

2. Solaris

Disable Network cards under boot Prom

Hi, I'm looking for a command to be able to disable a network card under the boot PROM. I need it to force my Jumpstart to use the Ethernet card of my server (V880) instead of my fiber card (gem0). Thanks, Fabien (6 Replies)
Discussion started by: unclefab
6 Replies

3. Solaris

How to List all Network cards

Hi, I'm looking for a command to be able to list all my network cards available on my server. With the command "ifconfig - a", I can only see to configured network card(s) Any idea ? :confused: Thanks a lot for your help, Fabien (5 Replies)
Discussion started by: unclefab
5 Replies

4. AIX

Load balancing across network cards

The title speaks for itself. I have never attempted this but understand there is a way to use two network cards (en0 and en1) with the same IP address so as to load balance the traffic flow through both cards. Anyone know the answer? (4 Replies)
Discussion started by: johnf
4 Replies

5. Solaris

How to find network cards available ...

Hi all, I have a server running with Solaris and I have 2 Pci cards installed on this server (since a while), 1 with 4 coppers connections output and one with a Fiber network connection output. Today, this server is using the on board network connection (Ce0). How can I find the other... (7 Replies)
Discussion started by: unclefab
7 Replies

6. HP-UX

routing issues with multiple NIC cards

I am running HP_UX 11.23 with 4 NIC cards (this is our TSM server) I have 4 subnets we are backing across. trying to keep traffic on their subnets. I only have one route statment should I add more. route add net 123.99.8.0 netmask 255.255.255.0 123.99.8.254 route add net 123.99.67.0 netmask... (2 Replies)
Discussion started by: myork
2 Replies

7. Solaris

qfe errors and network cards

Hi All, Hope you are all doing good. In MY unix box i have 2 network cards. I want to know what if one network card fails. Does the second one will automatically take all the traffic or how it is supposed to work. Also in my logs i am seeing below errors . Can you throw some light of this qfe... (3 Replies)
Discussion started by: Krrishv
3 Replies

8. Hardware

Slackware 13.1 can't configure two network cards

Hello everybody, I'm having troubles with Slackware 13.1 and network cards. I have one on-board Ethernet card (which is recognized and works okay) and a PCI Ethernet card (which is also recognized, but doesn't appear in 'ifconfig -a'). If i run a 'lspci', i can see the kernel recognized the... (5 Replies)
Discussion started by: semash!
5 Replies

9. UNIX for Dummies Questions & Answers

1 Server with 2 ethernet cards IP on seperate network. Possible?

Hi All, I have just setup a webserver running on a linux box. This server has 2 ethernet cards and only 1 is in used now. eg. 192.168.10.1 is my server IP. All users from 192.168.10.X can access my webserver. However, users from another LAN 10.10.10.X are not able to access my webserver. They... (0 Replies)
Discussion started by: jackma
0 Replies

10. Solaris

Network routing

hi, not an expert in Solaris networking so would like to ask your opinions Say i want to configure packet routing from source 10.126.120.130 (A) to destination 10.214.140.9 (B). I configured it this way (shown in netstat -rn) on (B) Destination Gateway Interface... (7 Replies)
Discussion started by: ghostdog74
7 Replies
DUMP_SOCKDFR(8) 					      System Manager's Manual						   DUMP_SOCKDFR(8)

NAME
dump_sockdfr - Display contents of frozen route file for SOCKS server SYNOPSIS
dump_sockdfr [infile] DESCRIPTION
dump_sockdfr reads in a frozen route file for the SOCKS server and produces a listing of its contents on the standard output. The argument is optional; if omitted, /etc/sockd.fr is assumed. The frozen route file is produced by make_sockdfr and is essentially the memory image of the parsed route file. Using the frozen route file can reduce the start-up delay of the SOCKS server program since it no longer has to parse the file contents. When the SOCKS server starts, it always looks for the frozen route file /etc/sockd.fr first. If that file is not found, it then tries to use the plain-text route file /etc/sockd.route. If you use frozen route file, you must remember to run make_sockdfr every time after you modify the plain-text file or the SOCKS server will continue to use the frozen version of a previous route file. FILES
/etc/sockd.fr, /etc/sockd.route SEE ALSO
make_sockdfr(8), sockd.fr(5), sockd.route(5) AUTHOR
Ying-Da Lee, yingda@esd.sgi.com or yingda@best.com May 6, 1996 DUMP_SOCKDFR(8)
All times are GMT -4. The time now is 05:09 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy