10-19-2009
Instalar SCO OPERSERVER 5.0.4
Tengo el cd de SCO OPERSERVER 5.0.4 pero en mi pc no tengo floppy para crear el diskette; aunque en el cd esta la imagen del diskette no se como sacarlo para poder instalar el sistema
Alguien podria indicarme como puedo instalarlo en el programa Sun xVM VirtualBox. ya que al iniciar de la imagen del cd que tengo me dice que no es booteable y cargo el archivo imagen del diskette y el empieza a bootear pero no me deja instalar sale un error
De antemano gracia por la ayuda
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How do I install an intel nic on sco 5.0.5 it did not detect when i installed the program:confused: (2 Replies)
Discussion started by: recono1
2 Replies
2. SCO
I have a SCO 5.0.7 server.As there is no parellel port ,printing is done via USB port.
After loading the Network Card driver ,during booting the server gets hanged and the NIC driver is not loaded.If the USB ports are disabled the NIC driver gets loaded.
As both USB and NIC driver are essential... (0 Replies)
Discussion started by: vikramviky
0 Replies
3. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
4. SCO
Hi
I am trying to install NIC FastNic 10/100 PCI Ethernet driver into PCI# 3 of the GA-SIML Rev 1.0 Motherboard on 1GB Hard-disk driveI have following the instruction on the CD-Disk and when I added NIC by netconfig and I do not know what is the following question:
PCI BUS#
DEVICE#... (3 Replies)
Discussion started by: TinhNhi
3 Replies
5. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
6. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
7. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
8. SCO
Sir I am trying to install UnixWare7.1.4 on vmware workstation9, virtualbox and I am getting the following error
FATAL BOOT ERROR: decompression failed
For installing SCO Unixware7.1.4 I have created virtual harddisk of size 18GB, 1024 RAM, 64bit video memory, chosen unixware7.1.4... (1 Reply)
Discussion started by: rupeshforu3
1 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
RXFORMAT(8) System Manager's Manual RXFORMAT(8)
NAME
rxformat - format floppy disks (2.11BSD)
SYNOPSIS
rxformat special
DESCRIPTION
The rxformat program formats a diskette in the specified drive associated with the special device special. Special is normally /dev/rrx0?,
for drive 0, or /dev/rrx1?, for drive 1, where ``?'' is either "a" or "b" to indicate single or double density access. The ``raw'' device
must be used. Single density is compatible with the IBM 3740 standard (128 bytes/sector). In double density, each sector contains 256
bytes of data.
Before formatting a diskette rxformat prompts for verification if standard input is a tty (this allows a user to cleanly abort the opera-
tion; note that formatting a diskette will destroy any existing data). Formatting is done by the hardware. All sectors are zero-filled.
DIAGNOSTICS
`No such device' means that the drive is not ready, usually because no disk is in the drive or the drive door is open. Other error mes-
sages are selfexplanatory.
FILES
/dev/rrx??
SEE ALSO
rx(4)
AUTHOR
Helge Skrivervik
BUGS
A floppy may not be formatted if the header info on sector 1, track 0 has been damaged. Hence, it is not possible to format a completely
degaussed disk. (This is actually a problem in the hardware.)
3rd Berkeley Distribution November 17, 1996 RXFORMAT(8)