10-19-2009
Instalar SCO OPERSERVER 5.0.4
Tengo el cd de SCO OPERSERVER 5.0.4 pero en mi pc no tengo floppy para crear el diskette; aunque en el cd esta la imagen del diskette no se como sacarlo para poder instalar el sistema
Alguien podria indicarme como puedo instalarlo en el programa Sun xVM VirtualBox. ya que al iniciar de la imagen del cd que tengo me dice que no es booteable y cargo el archivo imagen del diskette y el empieza a bootear pero no me deja instalar sale un error
De antemano gracia por la ayuda
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How do I install an intel nic on sco 5.0.5 it did not detect when i installed the program:confused: (2 Replies)
Discussion started by: recono1
2 Replies
2. SCO
I have a SCO 5.0.7 server.As there is no parellel port ,printing is done via USB port.
After loading the Network Card driver ,during booting the server gets hanged and the NIC driver is not loaded.If the USB ports are disabled the NIC driver gets loaded.
As both USB and NIC driver are essential... (0 Replies)
Discussion started by: vikramviky
0 Replies
3. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
4. SCO
Hi
I am trying to install NIC FastNic 10/100 PCI Ethernet driver into PCI# 3 of the GA-SIML Rev 1.0 Motherboard on 1GB Hard-disk driveI have following the instruction on the CD-Disk and when I added NIC by netconfig and I do not know what is the following question:
PCI BUS#
DEVICE#... (3 Replies)
Discussion started by: TinhNhi
3 Replies
5. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
6. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
7. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
8. SCO
Sir I am trying to install UnixWare7.1.4 on vmware workstation9, virtualbox and I am getting the following error
FATAL BOOT ERROR: decompression failed
For installing SCO Unixware7.1.4 I have created virtual harddisk of size 18GB, 1024 RAM, 64bit video memory, chosen unixware7.1.4... (1 Reply)
Discussion started by: rupeshforu3
1 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
FORMAT(1) General Commands Manual FORMAT(1)
NAME
format - format a PC floppy diskette
SYNOPSIS
format [-v] device [media-size [drive-size]]
DESCRIPTION
Format allows a user with read-write permission to device to format a floppy. Either one of the special floppy devices must be used, see
fd(4), or an automatic device may be used with the size of the floppy specified on the command line. Two sizes must be given when format-
ting a low density diskette in a high density drive. For example:
format /dev/at1
format /dev/fd1 1200
format /dev/fd1 360 1200
The first two commands format a 1.2M diskette, the last formats a 360k diskette in a 1.2M drive. A 1.44M drive knows when it's dealing
with a low density floppy, so all these commands format a 720k diskette:
format /dev/fd0 720
format /dev/fd0 720 1440
format /dev/ps0
No sizes may be specified when using a special floppy device, a size must be specified when using an automatic device.
OPTIONS
-v Verify the process by reading each track after formatting it. Formatting is normally blind, the controller has no idea whether it
succeeds or not. Use -v on a new box of cheap diskettes, or on a diskette that may have gone bad. Verifying will increase format-
ting time by 50%.
SEE ALSO
mkfs(1), fd(4).
DIAGNOSTICS
Numbers will be printed on standard output to show that it is busy. The locations of bad sectors are printed on standard error when veri-
fying. The exit code is zero unless there are too many bad spots.
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
FORMAT(1)