|
|
Sponsored Content
Top Forums
UNIX for Dummies Questions & Answers
Where do i put ifconfig & route add for boot?
Post 302363136 by vdi_jeanne on Monday 19th of October 2009 02:23:21 PM
10-19-2009
|
|
10 More Discussions You Might Find Interesting
1. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
2. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
3. UNIX for Dummies Questions & Answers
If I'm at a wireless cafe running SuSE and I want to read my mail but the wireless cafe blocks port 25 for smtp but I have a VPN connection to my home machine, how do I use the "route" command.
If I'm at home on my windows machine and have a VPN connection to another network, can I use the... (3 Replies)
Discussion started by: siegfried
3 Replies
4. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
5. UNIX for Dummies Questions & Answers
ignore (2 Replies)
Discussion started by: hairytorus
2 Replies
6. Solaris
hi,
I am trying to configure one of my interfaces, but after reboot - i lose the changes to the netmask & broadcast address.
I have added an entry in /etc/netmasks, but it doesnt pick up the new settings. any ideas - much appreciated.
before reboot:
eri0:... (3 Replies)
Discussion started by: badoshi
3 Replies
7. Shell Programming and Scripting
Hi,
I have a data as follow:
1, 1.0 4.00
1, 2.0 4.00
1, 3.0 4.43
1, 4.0 4.40
1, 5.0 4.48
2, 1.0 0.00
2, 2.0 4.40
2, 3.0 3.40
2, 4.0 4.40
2, 5.0 1.47
3, 1.0 1.00
3, 2.0 3.40
3, 3.0 2.40
3, 4.0 2.40
3, 5.0 2.40 (1 Reply)
Discussion started by: nica
1 Replies
8. Solaris
I have two ethernet interfaces nge0 and nge1.
An IP assigned on nge0 is 10.10.10.1/24 and on nge1 is 20.20.20.1/24. I want to make nge0 as primary interface.
My question here is,
1. Being nge0 as primary interface, if I ping to an IP 20.20.20.5, what will happen?
2. If the answer for the... (4 Replies)
Discussion started by: nthiruvenkatam
4 Replies
9. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
10. AIX
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
Discussion started by: witt
1 Replies
LEARN ABOUT ULTRIX
tcp-env
tcp-env(1) General Commands Manual tcp-env(1) NAME
tcp-env - set up TCP-related environment variables SYNOPSIS
tcp-env [ -rR ] [ -ttimeout ] program [ arg ... ] DESCRIPTION
The input for tcp-env must be a TCP connection. tcp-env finds out information about that connection, puts the information into several environment variables as described in tcp-environ(5), and runs program with the given arguments. Usually tcp-env is run from inetd. It might instead be run from another server that already sets up the right environment variables; if PROTO is set to TCP when tcp-env is invoked, tcp-env assumes that all the other variables are set up properly, and it does not check whether the input is a TCP connection. OPTIONS
-r (Default.) Attempt to obtain TCPREMOTEINFO from the remote host. -R Do not attempt to obtain TCPREMOTEINFO from the remote host. -ttimeout Give up on the TCPREMOTEINFO connection attempt after timeout seconds. Default: 30. SEE ALSO
tcp-environ(5), inetd(8) tcp-env(1)