10-12-2009
you can do this on the newer servers with an ILOM interface but not with a SF6800. i've never done this but there should be a WAN-boot option within jumpstart so you can boot a server over http. but you'll need a jumpstart server on the other end of the line.
one option you can maybe use is to setup a new domain inside the 6800 and use the old domain as a jumstart server. after installing the new solaris in the new domain you can add the remaining SB and IB board to the new domain and destroy the old one. but you need a minimum of two SB and IB boards to do this.
Last edited by DukeNuke2; 10-12-2009 at 11:53 AM..
10 More Discussions You Might Find Interesting
1. HP-UX
I've just completed a fresh install of HP-UX 11.0 on my 712/80 and everything starts up fine until it gets to the point where X kicks off and I believe at this point is supposed to launch into the CDE login.
It just sits there on the blank X screen with the X cursor for a minute or so then BEEPS... (9 Replies)
Discussion started by: ErikTheHAck
9 Replies
2. AIX
I've installed AIX 5.1 on a 43p-140, but am unable to log in. At no point in the install did it ask me for a root password. When it boots to the console prompt, I enter "root" as a username, and then after 1 second it cycles right back to another root prompt.
I am accessing the 43p-140... (4 Replies)
Discussion started by: akbar
4 Replies
3. Solaris
Hello,
For whatever reason, after installing Solaris 10 I can ping anything within my own LAN, including the router which is also set as the default gateway, but I have no internet connectivity with it. At first I thought this was a DNS issue, but I can't connect with external IP addresses... (3 Replies)
Discussion started by: Quadratic
3 Replies
4. Solaris
Hi Gurus
Recently i had download the ISO installer (sol-10-u8-ga-sparc-dvd.iso) for Solaris 10.
And i ftp to a Server.
May i know is it possible to install the Solaris by using this ISO file directly (not using network)? (8 Replies)
Discussion started by: SmartAntz
8 Replies
5. Solaris
Installing Solaris 8 for the first time...on a SunBlade 100. I have original Solaris 8 CD's.
About 45 minutes into the installation, the install halts with the following errors:
ERROR: Could not open file /a/etc/vfstab
ERROR: Could not create the file system mount table /etc/vfstab
I... (4 Replies)
Discussion started by: cdunavent
4 Replies
6. Solaris
Hello,
I am trying to install Solaris 10 on a newly created LDom. Here are the commands I ran to create the LDom:
ldm add-domain ldg2
ldm add-vcpu 8 ldg2
ldm add-memory 2g ldg2
ldm add-vnet vnet2 primary-vsw0 ldg2
ldm add-vdsdev /dev/dsk/c0t5000CCA01535E20Cd0s0 vol2@primary-vds0
ldm... (8 Replies)
Discussion started by: bstring
8 Replies
7. SCO
Trying to restore a 5.0.6 server to a new server but the owner doesnt have their install media. Saw that many people have this. Please let me know of anyone that has a download link. Much appreciation! (1 Reply)
Discussion started by: gavinseabrook
1 Replies
8. AIX
Hi Everyone,
I have been struggling for few days with iSCSI and thought I could get some help on the forum...
fresh install of AIX7.1 TL4 on Power 710, The rootvg relies on 3 SAS disks in RAID 0, 32GB Memory
The lpar Profile is using all of the managed system's resources.
I have connected... (11 Replies)
Discussion started by: frenchy59
11 Replies
9. Debian
Hello,
I have downloaded and install debian in computer it is blinking cursor what this mean? (6 Replies)
Discussion started by: Riteshkakkar
6 Replies
10. Solaris
I have M10-1. Installation OS 10 from cdrom external.
Here message from OK Prompt
{0} ok probe-scsi-all
/pci@8000/pci@4/pci@0/pci@2/pci@0/usb@4,1/cdrom@1
Unit 0 Removable Read Only device HL-DT-STDVDRAM GP65NB60 PF00
But..
{0} ok boot... (3 Replies)
Discussion started by: mbahjiman
3 Replies
LEARN ABOUT SUSE
install-solaris
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)