10-09-2009
I have 2 servers with this problem. I don't think that the problem is from my NICs.
In fact, I added a "broadcast" line in my configuration and then removed it. But the problem remained.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. Gentoo
Hi all,
I'm trying to write a script that will turn off the network interface eth0 on a linux Gentoo machine and then turn it back on, any help?
Thanks,
Neked (1 Reply)
Discussion started by: neked
1 Replies
3. Solaris
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Discussion started by: kumarmani
6 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
7. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. Solaris
Hi all, I'm new here and looking for some help.
I'm looking for the way to rename the network interfaces for Solaris 10. Got a server with 2 network cards (say "igb0" and "igb1") and there were some reasons that I have to swap the pci slots for those cards. However, after I did that, Solaris 10... (3 Replies)
Discussion started by: bbq9
3 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT CENTOS
report-cli
REPORT-CLI(1) LIBREPORT MANUAL REPORT-CLI(1)
NAME
report-cli - Work with ABRT problem directories from command line.
SYNOPSIS
report-cli [-vsp] -L[PREFIX] [PROBLEM_DIR]
report-cli [-vsp] -e EVENT PROBLEM_DIR
report-cli [-vsp] -a[y] PROBLEM_DIR
report-cli [-vsp] -c[y] PROBLEM_DIR
report-cli [-vsp] -r[y|o|d] PROBLEM_DIR
DESCRIPTION
report-cli is a command line tool that manages application crashes and other problems caught by abrtd daemon, or created by other programs
using libreport. It enables access to, manipulation of problem data, and reporting.
OPTIONS
-L[PREFIX]
List possible events [which start with PREFIX]
-e EVENT
Run EVENT on PROBLEM_DIR
-a, --analyze
Run analyze event(s) on PROBLEM_DIR
-c, --collect
Run collect event(s) on PROBLEM_DIR
-r, --report
Analyze, collect and report problem data in PROBLEM_DIR
-d, --delete
Remove PROBLEM_DIR after reporting
-y, --always
Noninteractive: don't ask questions, assume positive answer to all of them
-o, --report-only
With -r: do not run analyzers, run only reporters
-v, --verbose
Be verbose
-s
Log to syslog
-p
Add program names to log
-V, --version
Display version and exit
AUTHORS
o ABRT team
LIBREPORT 2.1.11 06/18/2014 REPORT-CLI(1)