10-07-2009
What should I explain in detail?
You can find a pretty good introduction to network programming
here.
10 More Discussions You Might Find Interesting
1. Programming
i am new in linux environment .I have used vi editor of Unix to get a programe compiled through "gcc ".kindly give me the options to get a program compiled & executed written in c on vi editor.
I want the command to compile a file and the command to get that compiled file executed with any... (2 Replies)
Discussion started by: Rajraius
2 Replies
2. Programming
i would like advice on the usbject of c programming (in the middle of reading a book on C). could i benefit more if i apply that knowledge in the unix format if i were able to, or would that take the point out of learning C, basically I want to stay away from strying too far away from unix and use... (1 Reply)
Discussion started by: moxxx68
1 Replies
3. Shell Programming and Scripting
Several months ago I found a link that explained the difference between how a Unix Systems Admin would do scripting compared to what a Unix Programmer would do.
It showed a basic script and then show several iterations that explained how the Systems Admin would change it to make it better. I was... (0 Replies)
Discussion started by: BCarlson
0 Replies
4. Programming
Sorry to ask this question here... where can I find a C++ programming thread? Thanks guys! (7 Replies)
Discussion started by: nadiamihu
7 Replies
5. Shell Programming and Scripting
Hello all!!
I am new to programming, and to this forum. :D
I am having sort of a problem. Me and my coworker are working on a code, both of us are stumped on a few things.
One is we have a whole log file, i have found how to extract by column, but not by row. I need to extract by both.:confused:... (7 Replies)
Discussion started by: xkayla06
7 Replies
6. UNIX for Dummies Questions & Answers
Hello,
I am trying to learn Networking Programming in C in unix enviorment. I want to know how good it is to become a network programmer. i am crazy about Network programming but i also want to opt for the best carreer options. Anybody experienced Network Programmer, please tell me is my... (5 Replies)
Discussion started by: vibhory2j
5 Replies
7. Programming
Can someone help me on suggesting some ways to access the memory content in RAM directly from C/C++ source code.
Please provide me any book name or any URL so that I can get an exhaustive
knowledge over it.
If possible please give me some tips on interacting with hardwares directly
through... (3 Replies)
Discussion started by: nandumishra
3 Replies
8. Shell Programming and Scripting
I have started writing one script. It is not taking the if block.
Here is the script:
#!/bin/sh
set USER='/usr/ucb/whoami'
#######################################################################
#Killing Process
#######################################################################... (6 Replies)
Discussion started by: amarpreetka
6 Replies
9. UNIX for Dummies Questions & Answers
How does unix system administration, unix programming, unix network programming differ?
Please help. (0 Replies)
Discussion started by: thulasidharan2k
0 Replies
10. UNIX for Dummies Questions & Answers
Hello.
I like Linux and C programming language. Allways wanted to understand kernel and become a Linux system programmer. And I also like Objective-C and iOS. These two programming areas have relations:
1. Linux and iOS are UNIX-like systems, POSIX compliant.
2. It is useful to know C language... (2 Replies)
Discussion started by: Rockatansky
2 Replies
FAITH(4) BSD Kernel Interfaces Manual FAITH(4)
NAME
faith -- IPv6-to-IPv4 TCP relay capturing interface
SYNOPSIS
device faith
DESCRIPTION
The faith interface captures IPv6 TCP traffic, for implementing userland IPv6-to-IPv4 TCP relay like faithd(8).
Each faith interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using
the cloned_interfaces variable in rc.conf(5).
Special action will be taken when IPv6 TCP traffic is seen on a router, and the routing table suggests to route it to the faith interface.
In this case, the packet will be accepted by the router, regardless of the list of IPv6 interface addresses assigned to the router. The
packet will be captured by an IPv6 TCP socket, if it has the IN6P_FAITH flag turned on and matching address/port pairs. As a result, faith
will let you capture IPv6 TCP traffic to some specific destination addresses. Userland programs, such as faithd(8) can use this behavior to
relay IPv6 TCP traffic to IPv4 TCP traffic. The program can accept some specific IPv6 TCP traffic, perform getsockname(2) to get the IPv6
destination address specified by the client, and perform application-specific address mapping to relay IPv6 TCP to IPv4 TCP.
The IN6P_FAITH flag on a IPv6 TCP socket can be set by using setsockopt(2), with level IPPROTO_IPV6 and optname IPv6_FAITH.
To handle error reports by ICMPv6, some ICMPv6 packets routed to an faith interface will be delivered to IPv6 TCP, as well.
To understand how faith can be used, take a look at the source code of faithd(8).
As the faith interface implements potentially dangerous operations, great care must be taken when configuring it. To avoid possible misuse,
the sysctl(8) variable net.inet6.ip6.keepfaith must be set to 1 prior to using the interface. When net.inet6.ip6.keepfaith is 0, no packets
will be captured by the faith interface.
The faith interface is intended to be used on routers, not on hosts.
SEE ALSO
inet(4), inet6(4), faithd(8)
Jun-ichiro itojun Hagino and Kazu Yamamoto, An IPv6-to-IPv4 transport relay translator, RFC3142.
HISTORY
The FAITH IPv6-to-IPv4 TCP relay translator first appeared in the WIDE hydrangea IPv6 stack.
BSD
April 10, 1999 BSD