09-24-2009
How many system disks does the POST report, and what condition are they in?
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
2. SCO
hi all
i use sco open server reliseas 5 on my system i get an image from system hard disk to another hard disk with acronis software and start system with new(backup)hard disk, but during the boot process some errors generate as follow
warning:hd:noroot disk controler was found
hd:a boot-time... (2 Replies)
Discussion started by: mehran_malek
2 Replies
3. HP-UX
Replace an unknown status controller on HP FC60 disk array
Author:JoyOnline JoyChangLu@gmail.com
Trouble description:
The users detected that the status of controller at A is unknown.
Analysis and diagnostic:
Physical observed all leds on enclosure of disk array is normal.
The... (4 Replies)
Discussion started by: JoyOnLine
4 Replies
4. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
5. Solaris
hi all
i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output
# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies
6. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
7. Solaris
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Discussion started by: kebabbert
2 Replies
8. Solaris
Hi All
Hope it's okay to post on this sub-forum, couldn't find a better place
I've got a 480R running solaris 8 with veritas volume manager managing all filesystems, including an encapsulated root disk (I believe the root disk is encapsulated as one of the root mirror disks has an entry under... (1 Reply)
Discussion started by: sunnyd76
1 Replies
9. Solaris
Hi
The scenario in the oracle t4-1 hardware with solaris 10 is as follows:
1. The initial install on the server was performed with an incorrect disk layout.
2. New disks were ordered and slot into the server.
3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
LEARN ABOUT MOJAVE
curlopt_postredir
CURLOPT_POSTREDIR(3) curl_easy_setopt options CURLOPT_POSTREDIR(3)
NAME
CURLOPT_POSTREDIR - how to act on a HTTP POST redirect
SYNOPSIS
#include <curl/curl.h>
CURLcode curl_easy_setopt(CURL *handle, CURLOPT_POSTREDIR,
long bitmask);
DESCRIPTION
Pass a bitmask to control how libcurl acts on redirects after POSTs that get a 301, 302 or 303 response back. A parameter with bit 0 set
(value CURL_REDIR_POST_301) tells the library to respect RFC 7231 (section 6.4.2 to 6.4.4) and not convert POST requests into GET requests
when following a 301 redirection. Setting bit 1 (value CURL_REDIR_POST_302) makes libcurl maintain the request method after a 302 redirect
whilst setting bit 2 (value CURL_REDIR_POST_303) makes libcurl maintain the request method after a 303 redirect. The value
CURL_REDIR_POST_ALL is a convenience define that sets all three bits.
The non-RFC behaviour is ubiquitous in web browsers, so the library does the conversion by default to maintain consistency. However, a
server may require a POST to remain a POST after such a redirection. This option is meaningful only when setting CURLOPT_FOLLOWLOCATION(3).
DEFAULT
0
PROTOCOLS
HTTP(S)
EXAMPLE
CURL *curl = curl_easy_init();
if(curl) {
curl_easy_setopt(curl, CURLOPT_URL, "http://example.com");
/* a silly POST example */
curl_easy_setopt(curl, CURLOPT_POSTFIELDS, "data=true");
/* example.com is redirected, so we tell libcurl to send POST on 301, 302 and
303 HTTP response codes */
curl_easy_setopt(curl, CURLOPT_POSTREDIR, CURL_REDIR_POST_ALL);
curl_easy_perform(curl);
}
AVAILABILITY
Added in 7.17.1. This option was known as CURLOPT_POST301 up to 7.19.0 as it only supported the 301 then. CURL_REDIR_POST_303 was added in
7.26.0.
RETURN VALUE
Returns CURLE_OK if the option is supported, and CURLE_UNKNOWN_OPTION if not.
SEE ALSO
CURLOPT_FOLLOWLOCATION(3), CURLOPT_POSTFIELDS(3),
libcurl 7.54.0 February 03, 2016 CURLOPT_POSTREDIR(3)