09-23-2009
Hi Greg, The additional interface will be directly linked to another computer - Not sure if a gateway is required in this case, but I'll try. Thx! Stephane
9 More Discussions You Might Find Interesting
1. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
2. Solaris
Hi All,
I recently installed Solaris 9 on my Compaq Presario V2000 Series (V2069CL) laptop. Everything is working fine except that Solaris is not able to detect the Network Interface after boot.
While the system is booting, it shows that it has detected "Xircom Pocket Ethernet parallel port... (3 Replies)
Discussion started by: com2com
3 Replies
3. Solaris
Hi All,
yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'.
I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Discussion started by: badoshi
2 Replies
4. Solaris
Please , I have a problem
I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline.
The system is in cluster mode (3.2)
route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51
-------------------
lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies
5. Solaris
Hi,
/sbin/ifconfig -a
when i login as guest user , output like below,
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2
inet... (5 Replies)
Discussion started by: forumguest
5 Replies
6. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
7. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
8. Solaris
Dear All,
I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface .
The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped.
But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies
9. Solaris
Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue:
Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies
LEARN ABOUT OPENSOLARIS
net_phylookup
net_phylookup(9F) Kernel Functions for Drivers net_phylookup(9F)
NAME
net_phylookup - determine if a network interface name exists for a network protocol
SYNOPSIS
#include <sys/neti.h>
phy_if_t net_phylookup(const net_data_t net, const char *name);
INTERFACE LEVEL
Solaris DDI specific (Solaris DDI).
PARAMETERS
net value returned from a successful call to net_protocol_lookup(9F).
name name of the network interface to find.
DESCRIPTION
The net_phylookup() function attempts to resolve the interface name passed in with the network protocol.
When called successfully, the value returned represents a network interface that exists, at the time of the call, within the scope of the
network interface. This value is only guaranteed to be unique for a name within the scope of the network protocol.
RETURN VALUES
The net_phylookup() function returns -1 if it is not supported by the network protocol, and 0 if the named network interface does not
exist (or is otherwise unknown). Otherwise, it returns a value greater than 0 representing a network interface that currently exists
within the scope of this network protocol.
CONTEXT
The net_phylookup() function may be called from user, kernel, or interrupt context.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Committed |
+-----------------------------+-----------------------------+
SEE ALSO
net_getifname(9F), net_phygetnext(9F), net_protocol_lookup(9F), attributes(5)
SunOS 5.11 1 May 2008 net_phylookup(9F)