09-23-2009
Hi Greg, The additional interface will be directly linked to another computer - Not sure if a gateway is required in this case, but I'll try. Thx! Stephane
9 More Discussions You Might Find Interesting
1. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
2. Solaris
Hi All,
I recently installed Solaris 9 on my Compaq Presario V2000 Series (V2069CL) laptop. Everything is working fine except that Solaris is not able to detect the Network Interface after boot.
While the system is booting, it shows that it has detected "Xircom Pocket Ethernet parallel port... (3 Replies)
Discussion started by: com2com
3 Replies
3. Solaris
Hi All,
yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'.
I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Discussion started by: badoshi
2 Replies
4. Solaris
Please , I have a problem
I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline.
The system is in cluster mode (3.2)
route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51
-------------------
lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies
5. Solaris
Hi,
/sbin/ifconfig -a
when i login as guest user , output like below,
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2
inet... (5 Replies)
Discussion started by: forumguest
5 Replies
6. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
7. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
8. Solaris
Dear All,
I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface .
The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped.
But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies
9. Solaris
Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue:
Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies
LEARN ABOUT FREEBSD
ipresend
IPRESEND(1) General Commands Manual IPRESEND(1)
NAME
ipresend - resend IP packets out to network
SYNOPSIS
ipresend [ -EHPRSTX ] [ -d <device> ] [ -g <gateway> ] [ -m <MTU> ] [ -r <filename> ]
DESCRIPTION
ipresend was designed to allow packets to be resent, once captured, back out onto the network for use in testing. ipresend supports a num-
ber of different file formats as input, including saved snoop/tcpdump binary data.
OPTIONS
-d <interface>
Set the interface name to be the name supplied. This is useful with the -P, -S, -T and -E options, where it is not otherwise possi-
ble to associate a packet with an interface. Normal "text packets" can override this setting.
-g <gateway>
Specify the hostname of the gateway through which to route packets. This is required whenever the destination host isn't directly
attached to the same network as the host from which you're sending.
-m <MTU>
Specify the MTU to be used when sending out packets. This option allows you to set a fake MTU, allowing the simulation of network
interfaces with small MTU's without setting them so.
-r <filename>
Specify the filename from which to take input. Default is stdin.
-E The input file is to be text output from etherfind. The text formats which are currently supported are those which result from the
following etherfind option combinations:
etherfind -n
etherfind -n -t
-H The input file is to be hex digits, representing the binary makeup of the packet. No length correction is made, if an incorrect
length is put in the IP header.
-P The input file specified by -i is a binary file produced using libpcap (i.e., tcpdump version 3). Packets are read from this file
as being input (for rule purposes).
-R When sending packets out, send them out "raw" (the way they came in). The only real significance here is that it will expect the
link layer (i.e. ethernet) headers to be prepended to the IP packet being output.
-S The input file is to be in "snoop" format (see RFC 1761). Packets are read from this file and used as input from any interface.
This is perhaps the most useful input type, currently.
-T The input file is to be text output from tcpdump. The text formats which are currently supported are those which result from the
following tcpdump option combinations:
tcpdump -n
tcpdump -nq
tcpdump -nqt
tcpdump -nqtt
tcpdump -nqte
-X The input file is composed of text descriptions of IP packets.
SEE ALSO
snoop(1m), tcpdump(8), etherfind(8c), ipftest(1), ipresend(1), iptest(1), bpf(4), dlpi(7p)
DIAGNOSTICS
Needs to be run as root.
BUGS
Not all of the input formats are sufficiently capable of introducing a wide enough variety of packets for them to be all useful in testing.
If you find any, please send email to me at darrenr@pobox.com
IPRESEND(1)