Sponsored Content
Operating Systems Solaris Route new network interface Solaris 8 Post 302355636 by gregsih on Wednesday 23rd of September 2009 09:26:46 AM
Old 09-23-2009
RE:Route new network interface Solaris 8

Hi Stephane

The first thing that springs to mind is the lack of a broadcast address on eri0. This should be something like 192.168.4.255 (You will need to check with your network team).

I would check the subnet mask as well. Given that the route get indicates a mask of 255.255.255.255 for 192.168.4.6 you will need the same for eri0.

Hope this helps.

Greg
 

9 More Discussions You Might Find Interesting

1. Solaris

network interface problem solaris 2.5

Hi guys, Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot). I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies

2. Solaris

Solaris 9 on x86- Can't detect network interface

Hi All, I recently installed Solaris 9 on my Compaq Presario V2000 Series (V2069CL) laptop. Everything is working fine except that Solaris is not able to detect the Network Interface after boot. While the system is booting, it shows that it has detected "Xircom Pocket Ethernet parallel port... (3 Replies)
Discussion started by: com2com
3 Replies

3. Solaris

Had to bounce interface to add network route

Hi All, yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'. I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Discussion started by: badoshi
2 Replies

4. Solaris

Network interface down after adding static route

Please , I have a problem I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline. The system is in cluster mode (3.2) route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51 ------------------- lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies

5. Solaris

Getting Network Interface details in solaris

Hi, /sbin/ifconfig -a when i login as guest user , output like below, lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2 inet... (5 Replies)
Discussion started by: forumguest
5 Replies

6. Solaris

route and interface configuration in solaris

Hi, Every time when i boot my system i have to manually issue the following commands. ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up route add default 192.168.200.1 I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies

7. Solaris

Configure network interface for Solaris 10

Hi, I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface. Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies

8. Solaris

Network Interface -- Solaris

Dear All, I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface . The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped. But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies

9. Solaris

Network interface configuration - Solaris 11

Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue: Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies
oidentd_masq.conf(5)						File Formats Manual					      oidentd_masq.conf(5)

NAME
oidentd_masq.conf - oidentd IP masquerading/NAT configuration file. DESCRIPTION
If you are using IP masquerading or NAT, oidentd can optionally return a username for connections from other machines. Support for this is specified by calling oidentd with the -m (or --masq) flag and by creating an /etc/oidentd_masq.conf file. oidentd can also forward requests for an IP masqueraded connection to the machine from which connection originates by way of the -f option. This will only work if the host to which the connection is forwarded is running oidentd with the -P (proxy) flag, or if the host's ident daemon will return a valid reply regardless of the input supplied by and the address of the host requesting the info (some ident daemons for windows do this, maybe others). FORMAT
<IP Address|Hostname>[/<Mask>] <Ident Response> <System Type> The first field contains the IP address or the hostname of a machine that IP masquerades through the machine on which oidentd runs. The mask parameter can be either a network mask or a mask in CIDR notation. A mask of 24 is equivalent to 255.255.255.0, a mask of 16 is equivalent to 255.255.0.0, etc. The second field specifies the reply that oidentd will return for lookups to the host matching the IP address specified in the first param- eter. The third field specifies the operating system the machine matching the first parameter is running. EXAMPLES
<Host>[/<Mask>] <Ident Response> <System Type> 192.168.1.1 someone UNIX 192.168.1.2 noone WINDOWS 192.168.1.1/32 user1 UNIX 192.168.1.0/24 user3 UNIX 192.168.0.0/16 user4 UNIX somehost user5 UNIX 192.168.1.0/255.255.255.0 user6 UNIX AUTHOR
Ryan McCabe <ryan@numb.org> http://dev.ojnk.net SEE ALSO
oidentd(8) oidentd.conf(5) version 2.0.8 13 Jul 2003 oidentd_masq.conf(5)
All times are GMT -4. The time now is 07:29 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy