Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Route new network interface Solaris 8
Operating Systems Solaris Route new network interface Solaris 8 Post 302355370 by sreiniche on Tuesday 22nd of September 2009 12:12:25 PM
Old 09-22-2009
Route new network interface Solaris 8
Hi there,


I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add -net 192.168.4.0/24 -interface eri0


Could someone please help me ?
I've had a look into this forum and did not find answers that could match this case.
Thanks to forgive me if I've missed up something...


Below various outputs from (I believe) useful commands:
#ifconfig -a:
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
ce0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 160.94.3.111 netmask fffffe00 broadcast 160.94.3.255
ether 0:3:baSmilie2a:db
eri0: flags=1000850<POINTOPOINT,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 192.168.4.5 netmask ffffff00
ether 0:3:baSmilie2a:db
#netstat -rn:
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
-------------------- -------------------- ----- ----- ------ ---------
140.94.2.0 140.94.3.111 U 1 12794 ce0
224.0.0.0 140.94.3.111 U 1 0 ce0
default 140.94.2.1 UG 1 20913
127.0.0.1 127.0.0.1 UH 386828356 lo0

#route get 192.168.4.6:
route to: 192.168.4.6
destination: 192.168.4.6
mask: 255.255.255.255
interface: ce0
flags: <UP,DONE>
recvpipe sendpipe ssthresh rtt,ms rttvar,ms hopcount mtu expire
0 0 0 0 0 0 1500 0


TIA!
Stephane
 

9 More Discussions You Might Find Interesting

1. Solaris

network interface problem solaris 2.5

Hi guys, Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot). I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies

2. Solaris

Solaris 9 on x86- Can't detect network interface

Hi All, I recently installed Solaris 9 on my Compaq Presario V2000 Series (V2069CL) laptop. Everything is working fine except that Solaris is not able to detect the Network Interface after boot. While the system is booting, it shows that it has detected "Xircom Pocket Ethernet parallel port... (3 Replies)
Discussion started by: com2com
3 Replies

3. Solaris

Had to bounce interface to add network route

Hi All, yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'. I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Discussion started by: badoshi
2 Replies

4. Solaris

Network interface down after adding static route

Please , I have a problem I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline. The system is in cluster mode (3.2) route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51 ------------------- lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies

5. Solaris

Getting Network Interface details in solaris

Hi, /sbin/ifconfig -a when i login as guest user , output like below, lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2 inet... (5 Replies)
Discussion started by: forumguest
5 Replies

6. Solaris

route and interface configuration in solaris

Hi, Every time when i boot my system i have to manually issue the following commands. ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up route add default 192.168.200.1 I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies

7. Solaris

Configure network interface for Solaris 10

Hi, I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface. Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies

8. Solaris

Network Interface -- Solaris

Dear All, I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface . The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped. But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies

9. Solaris

Network interface configuration - Solaris 11

Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue: Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies

LEARN ABOUT FREEBSD

nos-tun

NOS-TUN(8)						    BSD System Manager's Manual 						NOS-TUN(8)

NAME

     nos-tun -- implement ``nos'' or ``ka9q'' style IP over IP tunnel

SYNOPSIS

     nos-tun -t tunnel -s source -d destination -p protocol_number [source] target

DESCRIPTION

     The nos-tun utility is used to establish an nos style tunnel, (also known as ka9q or IP-IP tunnel) using a tun(4) kernel interface.

     Tunnel is the name of the tunnel device /dev/tun0 for example.

     Source and destination are the addresses used on the tunnel device.  If you configure the tunnel against a cisco router, use a netmask of
     ``255.255.255.252'' on the cisco.	This is because the tunnel is a point-to-point interface in the FreeBSD end, a concept cisco does not
     really implement.

     Protocol number sets tunnel mode.	Original KA9Q NOS uses 94 but many people use 4 on the worldwide backbone of ampr.org.

     Target is the address of the remote tunnel device, this must match the source address set on the remote end.

EXAMPLES

     This end, a FreeBSD box on address 192.168.59.34:

	   nos-tun -t /dev/tun0 -s 192.168.61.1 -d 192.168.61.2 192.168.56.45

     Remote cisco on address 192.168.56.45:

	   interface tunnel 0
	   ip address 192.168.61.2 255.255.255.252
	   tunnel mode nos
	   tunnel destination 192.168.59.34
	   tunnel source 192.168.56.45

AUTHORS

     Nickolay N. Dudorov <nnd@itfs.nsk.su> wrote the program, Poul-Henning Kamp <phk@FreeBSD.org> wrote the man-page.  Isao SEKI
     <iseki@gongon.com> added a new flag, IP protocol number.

BUGS

     We do not allow for setting our source address for multihomed machines.

BSD
								  April 11, 1998							       BSD
All times are GMT -4. The time now is 06:43 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy