hello, I am looking to make a script that will ping a remote ip address. Upon completion of the ping I want the program to either ping again if the # of packets transmitted is equal to the number of packets received or exit if the two values are unequal and information was lost. I am not sure if I... (3 Replies)
Hi there
i am busy compiling a script to ping a remote server, when the server is alive i get it to send me an sms, however i cant seem to make the ping stop, can somebody please help? please?
while (9)
set ans="`ping $IPaddress 1`"
if ( "$ans" == "IPaddress is alive" ) continue ... (5 Replies)
Hello all...I'm new to Unix and learning. What I'm trying to create is a script that will ping a known range of IP addresses, say 192.168.1.1 to 192.168.1.254. For each address that no reply is received, that address will be written to a log file that will be emailed to an administrator. My wife... (1 Reply)
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Hi. I have a server with multiple network ports that need to be tested to a list of destinations. I'm trying to write a scripts to automate this but can't seem to get past an error and could use some help.
I have two test files one contains the ip addresses of the onboard NICs and the other... (10 Replies)
Hello all!
This is my first post and I'm very new to programming. I would like help creating a simple perl or bash script that I will be using in my work as a junior bioinformatician.
Essentially, I would like to take a tab-delimted or .csv text with 3 columns and write them to a "3D" matrix:
... (16 Replies)
HI,
I have a file serverlist in that all host names are placed.
i have written a small script
#./testping
#! /bin/bash
for i in `cat serverlist`
do
ping $i >> output.txt
done
so now it creates a file output.txt till here fine..
now each time i run this script the output file... (4 Replies)
hello fellows,
I need help with a script, I'm using this one
HOSTS="192.168.10.9 192.168.10.15 "
SUBJECT="Attention - Gateway San Martin DOWN "
COUNT=1
EMAILID="lmail@mydomain.com"
for myHost in $HOSTS
do
count=$(ping -c $COUNT $myHost | grep 'received' | awk -F',' '{ print $2... (2 Replies)
I have a question is there any posibility for writing a script that you can see if a pc in your network is up of down , when you run this script for ex. ./test.sh 63 45 54 , which are the ip adresses of the computers , when you give the last digit of the ip adres as argument
63 , 45 and 54 are... (5 Replies)
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
LEARN ABOUT DEBIAN
mstack
VIEW-OS(1) General Commands Manual VIEW-OS(1)NAME
mstack - networking stack selection
SYNOPSIS
mstack [-hv] [-o protocol list] stack_mountpoint command
DESCRIPTION
In View-OS multiple networking stacks are available to processes at the same time. View-OS supports the msocket(2) system call. mstack
defines the default stack (for each address family) that is used when msocket refers to a NULL pathname for its stack. mstack provides
also a backward compatibility for all the programs using the obsolete socket(2) system call. The stack mountpoint identifies the stack. In
ViewOS it is the mountpoint where the stack was mounted (by mount(2)(8). In fact the call:
"socket(domain,type,protocol)"
is equivalent to:
"msocket(NULL,domain,type protocol)"
mstacks changes the default stack for the desired protocol families and executes the command (by execve(2)).
OPTIONS -h prints the mstack command usage
-v sets the verbose mode on
-o defines the list of protocols. Without a -o option, mstack redefines the default stack for all protocols families. The list of proto-
cols may include the a comma separated sequence of the following items: all, unix (or simply u), ipv4 (4), ipv6 (6), netlink (n),
packet (p), bluetooth (b), irda (i), ip (which include all ip related protocols ipv4, ipv6, netlink and packet), #n where n is the num-
ber of protocol. Each item can be prefixed by + or - to specify whether the protocol/group of protocols must be added or removed from
the set.
EXAMPLES
mstack /dev/net/lwip ip addr
lists the address managed by the stack mounted on /dev/net/lwip.
exec mstack /dev/net/null bash
disables the standard stack in a new bash (which overcomes the current one).
mstack -o ip /dev/net/lwip bash
starts a new bash which uses the stack /dev/net/lwip for ipv4 and ipv6 but not for the other protocols.
mstack -o -unix /dev/net/lwip bash
starts a new bash which uses the stack /dev/net/lwip for all protocols but AF_UNIX.
mstack -o +ip,-ipv6 /dev/net/lwip bash
starts a new bash which uses the stack /dev/net/lwip for ipv4, netlink, packet but not ipv6.
SEE ALSO umview(1), kmview(1), msocket(3), umnetnative(9), umnetnull(9), umnetlwipv6(9), unix(7), ip(7), ipv6(7), netlink(7), packet(7).
AUTHORS
View-OS is a project of the Computer Science Department, University of Bologna. Project Leader: Renzo Davoli.
<http://www.sourceforge.net/projects/view-os>
Howto's and further information can be found on the project wiki <wiki.virtualsquare.org>.
VIEW-OS: a process with a view April 23, 2008 VIEW-OS(1)