hi all,
have a ksh script where i am doing a
but for some reason it only writes 15 lines wheres when i run the same command manually from command prompt it prints out 60 lines.
why is it not writing the full 60 lines to the file ??
Hello,
The last line of prstat shows load average.
I am unable to figure out what actually it is.
I have read the man pages and also googled, all for no use.
Can somebody help me, as to what should be the avg. load of the system for best performance and how is this load of prstat calculated. (6 Replies)
Hi,
How to redirect the output of prstat command to a file.
Ex:
I want to do like this
while :
do
prstat >> prs.log
sleep 5
done
is it possible ???? if No, then how can i proceed??
PLEASE HELP ME OUT FROM THIS :confused:
Thanks in advance
----------- (2 Replies)
Good Evening everyone,
I am confused about prstat O/P as it shows memory values which are different from actual value.Below is the O/P of prstat command and swap commands.
NPROC USERNAME SIZE RSS MEMORY TIME CPU
48 root 2113M 1590M 1.2% 45:09.39 32%
31 daemon ... (7 Replies)
Can someone please explain me the "TIME" field of the output of "prstat -p<pid>" command ? The man page says it is "The cumulative execution time for the process". Does it mean how many hrs:min:sec the process is running ? If so then I'm not getting the desired output.
Can someone pls help me in... (5 Replies)
hi all,
was trying to figure out how busy my app was by looking at the performance of the app server. did a 'prstat -s rss' command to find the app servers using most memory.
Found a command 'prstat -m' which is meant to show more details on each pid but the output of this command... (1 Reply)
Hi,
I want to fire the prstat command which should run fro 60 secs and get the report into a text file using a script.
I just know the command:
prstat -c >> log.txt
which will run until we stop it.
But i want the script to run only for 60 sec,print the output to text file and stop... (3 Replies)
Hi Expert,
I want to print CPU and Memory utilization into a text file. I am using "prstat -Z" to see the output on screen. When I run below command
prstat -Z | grep httpd | awk '{print$3} '>> output.txt
but it is not printing to file. Also I want to be below header on output
PID USERNAME ... (6 Replies)
need help with formatting output of command top and prstat. My requirment is to remove few columns and display remaining . But when i used awk to do that the output seems to be have gone vague, mixing the column values.
After using awk to print particular column the output seems to have lost... (1 Reply)
Hi how to send below prstat script output into table format and send through email?
prstat|awk '{ if ($9 >= 5) print $0 }' (17 Replies)
Discussion started by: tharmendran
17 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)