09-08-2009
yeah... i had scsi RAID card attached to my server.. and im trying to configure RAID with my iinternal disk... there is 4 disks attached to the server... from what i get from the previous thread, they modify at the disk... correct me if im wrong...
if there is a guide of how to do it step by step that can be provided, greatly help...
9 More Discussions You Might Find Interesting
1. Solaris
hi all...sudhansu here............ i need some help..........
what is RAID 0+1 and RAID 1+0.............what is the difference between them................
suppose i have 80 gb disk space,then which RAID level i follow n why......... i need redundancy n maximum storage..........please help (3 Replies)
Discussion started by: sudhansu
3 Replies
2. Solaris
Somebody can help me ! how can i do mirror in sun ver 8
without third party software !!! (3 Replies)
Discussion started by: goldfelda
3 Replies
3. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
4. Solaris
Dear ALl,
I have a RAID 5 volume which is as below
d120 r 60GB c1t2d0s5 c1t3d0s5 c1t4d0s5 c1t5d0s5
d7 r 99GB c1t2d0s0 c1t3d0s0 c1t4d0s0 c1t5d0s0
d110 r 99GB c1t2d0s4 c1t3d0s4 c1t4d0s4 c1t5d0s4
d8 r 99GB c1t2d0s1 c1t3d0s1... (2 Replies)
Discussion started by: jegaraman
2 Replies
5. Solaris
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Discussion started by: Solarister
1 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. UNIX for Dummies Questions & Answers
Hi Gurus,
Can any one explain me the difference between hardware RAID and s/w RAID.
Thanks in Advance. (1 Reply)
Discussion started by: rama krishna
1 Replies
8. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
9. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT REDHAT
raidstop
raidstart(8) System Manager's Manual raidstart(8)
NAME
raidstart, raidstop, - command set to manage md devices.
SYNOPSIS
raidstart [options] <raiddevice>*
raidstop [options] <raiddevice>*
DESCRIPTION
RAID devices are virtual devices created from two or more real block devices. This allows multiple disks to be combined into a single
filesystem, possibly with automated backup and recovery. Linux RAID devices are implemented through the md device driver.
If you're using the /proc filesystem, /proc/mdstat gives you informations about md devices status.
Currently, Linux supports linear md devices, RAID0 (striping), RAID1 (mirrroring), and RAID4 and RAID5. For information on the various lev-
els of RAID, check out:
http://ostenfeld.dk/~jakob/Software-RAID.HOWTO/
for new releases of the RAID driver check out:
ftp://ftp.fi.kernel.org/pub/linux/daemons/raid/alpha
Avaible commands are :
mkraid : configures (creates) md (RAID) devices in the kernel, banding multiple devices into one.
raidstart : activates (starts) an existing 'persistent' md device
raid0run : activates old nonpersistent RAID0/LINEAR md devices
raidstop : turns off an md device, and unconfigures (stops) it
By default, a systems RAID configuration is kept in /etc/raidtab, which can configure multiple RAID devices.
All of these tools work similiarly. If -a (or --all) is specified, the specified operation is performed on all of the RAID devices men-
tioned in the configuration file. Otherwise, one or more RAID devices must be specified on the command line. For example:
raid0run -a
Starts all of the 'old' RAID0 RAID devices specified in /etc/raidtab. If only /dev/md1 should be started, the following command should be
used instead:
raidstart /dev/md1
OPTIONS
-a, --all
Apply the command to all of the configurations specified in the config file.
-c, --configfile filename
Use filename as the configuration file (/etc/raidtab is used by default).
-h, --help
Displays a short usage message, then exits.
-V, --version
Displays a short version message, then exits.
NOTES
The raidtools are derived from the md-tools and raidtools packages, which were originally written by Marc Zyngier, Miguel de Icaza, Gadi
Oxman, Bradley Ward Allen, and Ingo Molnar.
BUGS
no known bugs.
SEE ALSO
raidtab(5), raid0run(8), raidstop(8), mkraid(8)
raidstart(8)