Im calculating file sizes with below AWK script. I do this before some spesific files are transferred. I run the script it works but after several running it stuck with a limit of 2147483647 (2 Gbytes -1 byte) and cant exceed this. Something is wrong and I can't proceed, would appreciate any help.
i find .gz, .tar or .rar files which are older than 1 day under a main directory and execute "ls -l" and calculate sizes but i also print 6th and 7th columns too into same file just for info.Then using 3rd colums i calculate the all sizes as a total sum.
The output of script is like below (sum of bytes above file) :
---------- Post updated at 05:12 PM ---------- Previous update was at 03:41 PM ----------
I'm afraid my system does not support 64 bits of aritmethic operations
Please advise, is my system unsufficient for such aritmethic operations and should i upgrade the solaris version to 64-Bit exec SPARC?
I have been using x=ls -la "$f" | awk '{print $5}'
This allows me to the size of all the files in $f and echo $x later .
The only problem is instead of protecting the file size format of ls -la which is right to left, it rearranges it and reads it left to right.
Cyborg was kind... (1 Reply)
Hallo all,
I have a script which creates an output ... see below:
root@a7germ:/tmp/pax > cat 20061117.txt
523.047
521.273
521.034
517.367
516.553
517.793
513.114
513.940
I would like to use awk to calculate the (a)total sum of the numbers (b) The average of the numbers.
Please... (4 Replies)
Hello!
I need to write partitioning script wich would work in rescue mode. It will prepare partitions and unpack linux on it. However I need to calculate whole size of the disk and create:
/dev/sda1 --> One big partition (minus (2*size of memory) for swap)
/dev/sda2 --> Swap partition... (1 Reply)
I have a list of coordinate data, sampled below.
54555209 784672723
I want it as:
545552.09 7846727.23
Below is my script:
BEGIN {FS= " "; OFS= ","} {print $1*.01,$2*.01}
This is my outcome:
5.5e7 7.8e8
How do I tell awk that I want to keep all the digits instead of outputting... (1 Reply)
My code is
awk '{
out=split(FILENAME,a,"/")
sub(/\./,"_",a)
sub(/\-/,"_",a)
NEWSTRING="main_"a"_"a"(" # The word we want to insert
gsub(/main\(/,NEWSTRING); # the word to be replaced
print "Main becomes ",NEWSTRING")","in file ",FILENAME >> "/home/ds2/test/NEW2.txt" ... (4 Replies)
hi there again,
i need to do a simple division with my data with a number of rows. i think i wanted to have a simple output like this one:
col1 col2 col3
val1 val2 val1/val2
valn valm valn/valm
any suggestion is very much appreciated. thanks much. (2 Replies)
I am trying to run the awk below. My question is when I split the input, then run anotherawk to perform a calculation using that splitas the input there are no issues. When I try to combine them the output is not correct, is the split not working or did I do it wrong? Thank you :).
input
... (8 Replies)
In the below awk, I am trying to calculate percent for a given id. It is very close the problem is when the # being used in the calculation is zero. I am not sure how to code this condition into the awk as it happens frequently. The portion in italics was an attempt but that lead to an error. Thank... (13 Replies)
i have a file say test with the below mentioned details
Folder Name Total space Space used
/test/test1 500.1GB 112.0 GB
/test/test2 3.2 TB 5TB
/test/test3 3TB 100GB
i need to calculate percentage of each row based on total space and space used and copy... (9 Replies)
Discussion started by: venkitesh
9 Replies
LEARN ABOUT OPENSOLARIS
rpm2cpio
rpm2cpio(1) User Commands rpm2cpio(1)NAME
rpm2cpio - convert Red Hat Package (RPM) to cpio archive
SYNOPSIS
rpm2cpio [file.rpm]
DESCRIPTION
The rpm2cpio utility converts the .rpm file specified as its sole argument to a cpio archive on standard output. (See NOTES.) If no argu-
ment is given, an rpm stream is read from standard input. In both cases, rpm2cpio will fail and print a usage message if the standard out-
put is a terminal. Therefore, the output is usually redirected to a file or piped through the cpio(1) utility.
EXAMPLES
Example 1 Converting an rpm file
example% rpm2cpio Device3Dfx-1.1-2.src.rpm | cpio -itv
CPIO archive found!
-rw-r--r-- 1 root root 2635 Sep 13 16:39 1998, 3dfx.gif
-rw-r--r-- 1 root root 11339 Sep 27 16:03 1998, Dev3Dfx.tar.gz
-rw-r--r-- 1 root root 1387 Sep 27 16:04 1998, Device3Dfx-1.1-2.spec
31 blocks
Example 2 Converting from standard input
example% rpm2cpio < Device3Dfx-1.1-2.src.rpm | cpio -itv
CPIO archive found!
-rw-r--r-- 1 root root 2635 Sep 13 16:39 1998, 3dfx.gif
-rw-r--r-- 1 root root 11339 Sep 27 16:03 1998, Dev3Dfx.tar.gz
-rw-r--r-- 1 root root 1387 Sep 27 16:04 1998, Device3Dfx-1.1-2.spec
31 blocks
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWrpm |
+-----------------------------+-----------------------------+
SEE ALSO cpio(1), attributes(5)NOTES
rpm2cpio handles versions 3 and 4 RPMs.
SunOS 5.11 20 Aug 2001 rpm2cpio(1)