08-29-2009
Invoke ifconfig and write down the two HWaddr strings. These are the MAC addresses for the NICs.
On way is to remove one NIC and check for a label with its MAC address. There is usually a label with the MAC address somewhere on the NIC.
Alternatively if you are connected to a router, you should be able to figure out the MAC address of each NIC from the port it is attached to.
Alternatively install Wireshark, monitor one NIC and drill down into a source packet to determine the MAC address.
9 More Discussions You Might Find Interesting
1. Linux
Hi
I had a DL380 with two two port eth cards. I now replaced one with a four port eth card and my interfaces seemed to have jumped around.
Is there a method of moving eth ports... eg making port eth4 eth2.:confused: (2 Replies)
Discussion started by: theroncj
2 Replies
2. Solaris
Hi everyone,
I am hoping anyone of you could help me in this weird problem we have in 1 of our Solaris 10 servers. Lately, we have been having some ftp problems in this server. Though it can ping any server within the network, it seems that it can only ftp to a select few. For most servers, the... (4 Replies)
Discussion started by: labdakos
4 Replies
3. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
4. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
5. Shell Programming and Scripting
I want to run dhcpclient for all the eth* which has no ip
for example
eth0 Link encap:Ethernet HWaddr 00:1E:67:3E:BA:EF
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0... (6 Replies)
Discussion started by: yanglei_fage
6 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. UNIX for Dummies Questions & Answers
hi guys
I have a server which has 2 nics eth0 and eth1
eth0 is used for our email traffic server. everything working fine
some time later a eth1 was added for backup purposes so this new nic sends data to another vlan for backup purposes
all of a sudden our mail server starts to fail... (3 Replies)
Discussion started by: karlochacon
3 Replies
8. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
9. UNIX for Advanced & Expert Users
Dear all,
I have a remote CentOS7 server that has two network cards. Each card has four ports and port one of card one was defined with the IP address assigned to the server. So far, so good and it's been working for over a year. We have now got cables sorted out so there are four paths... (4 Replies)
Discussion started by: rbatte1
4 Replies
LEARN ABOUT DEBIAN
setether
SETETHER(8) System Manager's Manual SETETHER(8)
NAME
setether - Set the ethernet address for use with DECnet
SYNOPSIS
setether <if> [<if>...]|all [options]
DESCRIPTION
Set ethernet MAC address on ethernet adaptors
This script should be run at system startup. It will change the ethernet hardware (MAC) address of any or all ethernet interfaces to match
the DECnet node address. DECnet requires that the MAC address of all ethernet adaptors running the protocol be set approriately. If you do
not run setether then you must change the ethernet address in some other way for DECnet to work.
By default no ethernet interfaces will have their MAC addresses changed by setether, if you specify all then all interfaces name eth* will
be changed, otherwise a list of interface names can be specified. setether will enable (UP) all interfaces it changes the MAC addresses
of.
(2.4 only) The first interface specified on the command-line will also be made the default interface for DECnet operations (ie attempts to
contact nodes not in the neighbour table will be done over this interface).
This script must be run with the interface inactive, it is normally run from /etc/init.d/decnet before TCP/IP starts up.
EXAMPLES
set the MAC address of eth0.
# /sbin/setether eth0
set the MAC address of all ethernet interfaces
# /sbin/setether all
HELPFUL HINTS
If you have multiple ethernet cards on your system and they are connected to the the same network you should specify which one you want to
use for DECnet communication on the setether command line, otherwise they will both be given the same MAC address and this is probably not
what you want.
Running DECnet on multiple ethernet interfaces only works under Linux 2.4. If you are running Linux 2.2 then the interface name on the
setether command line must match the one in /etc/decnet.conf(5).
SEE ALSO
decnet.conf(5), dntype(1), dndir(1), dndel(1), dnetd(8), dnping(1)
DECnet utilities March 01 2001 SETETHER(8)