08-28-2009
Quote:
Originally Posted by
solarisadm
In Solaris 10, mpxio is enabled in /kernel/drv/fp.conf.
I enable MPxIO using "stmsboot -e". It will adjust fp.conf and mpt.conf as needed.
When executing "stmsboot -e" it will show a list of multipath-capable controllers.
My iSCSI adapters dont show up there.
scsi_vhci.conf is used so the system recognizes third party devices.
iscsi.conf is specifically for iscsi ports.
10 More Discussions You Might Find Interesting
1. Solaris
hi,
I have installed Solaris 10 10/08 on sparc machine. I would like to configure iSCSI on that to mount SAN Volumes. Is there any need to install any additional patches for iSCSI to work.
Thanks,
Prashant. (4 Replies)
Discussion started by: prashantbhushan
4 Replies
2. Solaris
Hello!
I have several disks discovered using iscsi protocol.
There disks are represented in OS like c2txd0 .
logs:
Is it possible to change drive path, for example, from c2t6d0 to c2t7d0?
It's important for me because I have to install oracle RAC on RAW devices.
NIck (0 Replies)
Discussion started by: skelet
0 Replies
3. UNIX for Advanced & Expert Users
I am running Solaris 10 on a V490. I have Dell EqualLogic SAN attached.
I would like to take full advantage of the iSCSI initiator.
I have a primary network interface and IP addresses for all four SAN ports. Since the four ports are SUN GigaSwift (legacy), I cannot utilize dladm, so I downloaded... (2 Replies)
Discussion started by: KSFlyer
2 Replies
4. UNIX for Dummies Questions & Answers
how to change ethernet cable of iscsi initiator (iscsi client) (0 Replies)
Discussion started by: pankajd
0 Replies
5. Solaris
I have been running some tests with solaris mpxio, dual-pathed to HDS SAN storage.
When I take a path offline, Solaris recognised this and a path is shown as offline in luxadm display <device>. However, it does not recover on reinstatement of the path until I run cfgadm -al.
Any ideas?
Phil (3 Replies)
Discussion started by: UKPhil
3 Replies
6. Solaris
Im not able to turn the multipath off on the solaris s10 X86...since im on FC boot..
if i disable multipath , from /kernel/drv/iscsi.conf then im not able to boot the machine.:wall:
Is there any other go or any suggestions . (2 Replies)
Discussion started by: gowtham.varma
2 Replies
7. Solaris
Hi,
I have an Oracle/Sun T3-2 Server with a duel SAS controller Fujitsu DX60 array attached.
I have 2 x SAS HBA's in the T3-2. One HBA cabled to CM0 and one HBA cabled to CM1 of the array.
The array is setup with one RAID GROUP and one VOLUME and one LUN
In Solaris I can see one device... (4 Replies)
Discussion started by: general_lee
4 Replies
8. Solaris
hi to all
i've done that steps, but i was not completely successful:
sudo pkg install group/feature/storage-server
sudo svcadm enable stmf
sudo zfs create -V 1g rpool/LUN1
sudo stmfadm create-lu /dev/zvol/rdsk/rpool/LUN1
sudo stmfadm list-lu ... (4 Replies)
Discussion started by: jm83
4 Replies
9. Solaris
Hi Community,
I am facing one issue related storage accessing from solaris 10 machine(M5000). it was working fine then we shifted to another site. the only change on that site is FC switch.
The issue i am facing is from solaris machine i can able to see the LUN, it;s only a test lun of 30... (17 Replies)
Discussion started by: bentech4u
17 Replies
10. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
LEARN ABOUT OPENSOLARIS
iscsitgtd
iscsitgtd(1M) System Administration Commands iscsitgtd(1M)
NAME
iscsitgtd - iSCSI Target daemon
SYNOPSIS
iscsitgtd [-d door_file]
DESCRIPTION
The iscsitgtd daemon process implements the iSCSI configuration, control, and data paths, providing iSCSI Target Mode support in the
Solaris operating system.
The configuration and control path is by means of the Solaris Doors subsystem (see door_create(3C)), and provides the interface between
the iSCSI Target administration utility, iscsitadm(1M), persistence configuration data stored in the Service Configuration Facility (SCF)
of the service management facility (SMF). See smf(5).
The data path managed by the daemon exists between TPC/IP port 3260, and the files, block devices, or raw SCSI devices configured as iSCSI
target LUNs.
OPTIONS
The following options is supported:
-d door_file
Override the location of the Solaris Door used for configuration from /var/run/iscsi_tgt_door to a door of one's choosing.
Solaris Configuration Facility (SCF)
The following options are supported:
PGR-basedir
SCSI-3 PGR base directory for ZVOL failover. Set to /.
daemonize
Run as Solaris daemon process. Either true or false.
dbg-lvl
Runtime debug level to console.
qlog-lvl
Runtime logging to /tmp/target_log.
The following are the logging values, in hexadecimal.
0x00001 - Connection errors
0x00002 - Connection login errors
0x00004 - Connection Non-I/O errors
0x00008 - Connection I/O errors
0x00010 - Session errors
0x00020 - Session login errors
0x00040 - Session Non-I/O errors
0x00080 - Session I/O errors
0x00100 - Emulation errors
0x00200 - Emulation Non-I/O errors
0x00400 - Emulation I/O errors
0x01000 - General errors
0x02000 - General details
0x04000 - iSNS details
0x10000 - SCSI-3 PGR errors
0x20000 - SCSI-3 PGR Non-I/O errors
0x40000 - SCSI-3 PGR I/O errors
EXAMPLES
Example 1 Listing All iscsitgt Values
The following commands lists all iscsitgt values.
# svccfg -s iscsitgt listprop iscsitgt
Example 2 Setting SCF Options
The following command sets the PGR-basedir option.
# svccfg -s iscsitgt setprop iscsitgt/PGR-basedir = astring: "/"
The following command sets the dbg-lvl option.
# svccfg -s iscsitgt setprop iscsitgt/dbg-lvl = integer: 0x80ffffff
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWiscsitgtu |
+-----------------------------+-----------------------------+
|Interface Stability |Volatile |
+-----------------------------+-----------------------------+
SEE ALSO
iscsitadm(1M), door_create(3C), attributes(5), smf(5)
NOTES
The iSCSI Target daemon, iscsitgtd, is managed by the service management facility, smf(5), under the fault management resource identifier:
svc:/system/iscsitgt:default
SunOS 5.11 16 Mar 2009 iscsitgtd(1M)