08-28-2009
Hi Zaxxon,
all these nodes are planned to be in the same cluster - I will have one more cluster as DR solution and one more cluster as uat - all of them have 7 lpars each if I am done
I have just spoken to the SAN guys - they dont see any problems making all 7 nodes see the same disks ... one problem less
Kind regards
Nicki
10 More Discussions You Might Find Interesting
1. AIX
Hi Guys,
I have two nodes clustered. Each node is AIX 5.2 & they are clustered with HACMP 5.2. The mode of the cluster is Active/Passive which mean one node is the Active node & have all resource groups on it & the 2nd node is standby.
Last Monday I noted that all resource groupes have been... (2 Replies)
Discussion started by: aldowsary
2 Replies
2. AIX
Hi
Can ony one advise which files can be deleted in /usr in an aix hacmp node ? Im new to aix and Im not sure which files can be deleted ?
#df -g /usr
Filesystem GB blocks Free %Used Iused %Iused Mounted on
/dev/hd2 7.00 1.00 86% 67013 22% /usr
... (4 Replies)
Discussion started by: samsungsamsung
4 Replies
3. AIX
This post just as a follow-up for thread https://www.unix.com/aix/115548-hacmp-5-4-aix-5300-10-not-working.html: there was a bug in the clcomdES that would cause the Two-Node-Cluster-Configuration-Assistant to fail even with a correct TCP/IP adapter setup. That affected HACMP 5.4.1 in combinatin... (0 Replies)
Discussion started by: shockneck
0 Replies
4. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
5. AIX
Hi,
I have a running HACMP Cluster with two nodes. Its working in active/passive mode. (i.e Out of the two nodes in the cluster one will be active and the other one will be on standby. If first node fails the other takes over)
1. There is a Service IP associated with the cluster. Now the... (2 Replies)
Discussion started by: aixromeo
2 Replies
6. AIX
Hi,
I have a IBM Power series machine that has 2 VIOs and hosting 20 LPARS.
I have two LPARs on which GPFS is configured (4-5 disks)
Now these two LPARs need to be configured for HACMP (PowerHA) as well.
What is recommended? Is it possible that HACMP can be done on this config or do i... (1 Reply)
Discussion started by: aixromeo
1 Replies
7. AIX
HACMP two-node cluster with mirrored LVM.
HACMP two-node cluster with two SAN storages mirrored using LVM. Configured 2 disk heartbeat networks - 1 per each SAN storage. While performing redundancy tests. Once one of SAN storage is down - cluster is going to ERROR state. What are the guidelines... (2 Replies)
Discussion started by: OdilPVC
2 Replies
8. AIX
Hello AIX experts,
I have few queries and appreciate if you could help me with them.
1. How to check if HACMP (or any other AIX OS cluster) is installed
2. How to check if HACMP (or any other AIX OS cluster) is running
3. how to check which Oracle DB instance is running on it
4. how to... (1 Reply)
Discussion started by: prvnrk
1 Replies
9. AIX
Folks,
Please have a look to the attached screenshot from my managed node's HEA configuration option page. I would like to know - what does "Flow Control Enabled" checkbox help us with if opted for?
Thanks!
-- Souvik (3 Replies)
Discussion started by: thisissouvik
3 Replies
10. AIX
Dear all
i have two aix system
-Model : P770
-OS version: AIX 6.1
-patch level : 6100-07-04-1216
-ha version : HACMP v 6.1.0.8
-host : A, B
last Wednesday, my B system suddenly went down with crash dump. after 1 minute, A system went down with crash dump. I checked the dump of A-system... (6 Replies)
Discussion started by: tomato00
6 Replies
LEARN ABOUT DEBIAN
mkqdisk
mkqdisk(8) Quorum Disk Management mkqdisk(8)
NAME
mkqdisk - Cluster Quorum Disk Utility
WARNING
Use of this command can cause the cluster to malfunction.
SYNOPSIS
mkqdisk [-?|-h] | [-L] | [-f label] [-c device -l label] [-d [-d ...]]
DESCRIPTION
The mkqdisk command is used to create a new quorum disk or display existing quorum disks accessible from a given cluster node.
OPTIONS
-c device -l label
Initialize a new cluster quorum disk. This will destroy all data on the given device. If a cluster is currently using that device
as a quorum disk, the entire cluster will malfunction. Do not run this on an active cluster when qdiskd is running. Only one
device on the SAN should ever have the given label; using multiple different devices is currently not supported (it is expected a
RAID array is used for quorum disk redundancy). The label can be any textual string up to 127 characters - and is therefore enough
space to hold a UUID created with uuidgen(1).
-f label
Find the cluster quorum disk with the given label and display information about it.
-L Display information on all accessible cluster quorum disks.
-d Increase debugging level. Specify multiple times for more information. Currently, specifying more than twice has no effect.
SEE ALSO
qdisk(5), qdiskd(8), uuidgen(1)
July 2006 mkqdisk(8)