08-28-2009
How many locations are involved (servers and SAN)?
10 More Discussions You Might Find Interesting
1. AIX
Hi Guys,
I have two nodes clustered. Each node is AIX 5.2 & they are clustered with HACMP 5.2. The mode of the cluster is Active/Passive which mean one node is the Active node & have all resource groups on it & the 2nd node is standby.
Last Monday I noted that all resource groupes have been... (2 Replies)
Discussion started by: aldowsary
2 Replies
2. AIX
Hi
Can ony one advise which files can be deleted in /usr in an aix hacmp node ? Im new to aix and Im not sure which files can be deleted ?
#df -g /usr
Filesystem GB blocks Free %Used Iused %Iused Mounted on
/dev/hd2 7.00 1.00 86% 67013 22% /usr
... (4 Replies)
Discussion started by: samsungsamsung
4 Replies
3. AIX
This post just as a follow-up for thread https://www.unix.com/aix/115548-hacmp-5-4-aix-5300-10-not-working.html: there was a bug in the clcomdES that would cause the Two-Node-Cluster-Configuration-Assistant to fail even with a correct TCP/IP adapter setup. That affected HACMP 5.4.1 in combinatin... (0 Replies)
Discussion started by: shockneck
0 Replies
4. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
5. AIX
Hi,
I have a running HACMP Cluster with two nodes. Its working in active/passive mode. (i.e Out of the two nodes in the cluster one will be active and the other one will be on standby. If first node fails the other takes over)
1. There is a Service IP associated with the cluster. Now the... (2 Replies)
Discussion started by: aixromeo
2 Replies
6. AIX
Hi,
I have a IBM Power series machine that has 2 VIOs and hosting 20 LPARS.
I have two LPARs on which GPFS is configured (4-5 disks)
Now these two LPARs need to be configured for HACMP (PowerHA) as well.
What is recommended? Is it possible that HACMP can be done on this config or do i... (1 Reply)
Discussion started by: aixromeo
1 Replies
7. AIX
HACMP two-node cluster with mirrored LVM.
HACMP two-node cluster with two SAN storages mirrored using LVM. Configured 2 disk heartbeat networks - 1 per each SAN storage. While performing redundancy tests. Once one of SAN storage is down - cluster is going to ERROR state. What are the guidelines... (2 Replies)
Discussion started by: OdilPVC
2 Replies
8. AIX
Hello AIX experts,
I have few queries and appreciate if you could help me with them.
1. How to check if HACMP (or any other AIX OS cluster) is installed
2. How to check if HACMP (or any other AIX OS cluster) is running
3. how to check which Oracle DB instance is running on it
4. how to... (1 Reply)
Discussion started by: prvnrk
1 Replies
9. AIX
Folks,
Please have a look to the attached screenshot from my managed node's HEA configuration option page. I would like to know - what does "Flow Control Enabled" checkbox help us with if opted for?
Thanks!
-- Souvik (3 Replies)
Discussion started by: thisissouvik
3 Replies
10. AIX
Dear all
i have two aix system
-Model : P770
-OS version: AIX 6.1
-patch level : 6100-07-04-1216
-ha version : HACMP v 6.1.0.8
-host : A, B
last Wednesday, my B system suddenly went down with crash dump. after 1 minute, A system went down with crash dump. I checked the dump of A-system... (6 Replies)
Discussion started by: tomato00
6 Replies
LEARN ABOUT HPUX
cmhaltnode
cmhaltnode(1m) cmhaltnode(1m)
NAME
cmhaltnode - halt a node in a high availability cluster
SYNOPSIS
cmhaltnode [-f] [-v] [-t] [node_name...]
DESCRIPTION
cmhaltnode causes a node to halt its cluster daemon and remove itself from the existing cluster.
To halt cluster on the node, a user must either be superuser(UID=0), or have an access policy of FULL_ADMIN allowed in the cluster configu-
ration file. See access policy in cmquerycl.
When cmhaltnode is run on a node, the cluster daemon is halted and, optionally, all packages that were running on that node are moved to
other nodes if possible.
If node_name is not specified, the cluster daemon running on the local node will be halted and removed from the existing cluster.
If you issue this command while a cluster is still in the process of forming, the command will fail with the message "Unable to connect to
daemon." If this happens, wait for the cluster to form successfully, then issue the command again.
Options
cmhaltnode supports the following options:
-f Force the node to halt even if there are packages or group members running on it. The group members on the node will be
terminated. The halt scripts for all packages running on the node will be run; based on priority or dependency relation-
ships, this may affect packages on other nodes. In other words, packages on other nodes may either start or halt based on
this package halting. If the package configuration and current cluster membership permit, and if the package halt script
succeeds, the packages will be started on other nodes. Without this option, if packages are running on the given node,
the command will fail. If a package fails to halt, the node halt will also fail.
-v Verbose output will be displayed.
-t Test only. Provide an assessment of the package placement without affecting the current state of the nodes or packages.
This option validates the node's eligibility with respect to the package dependencies as well as the external dependencies
such as EMS resources, package subnets, and storage before predicting any package placement decisions. If there is a pack-
age in maintenance mode running on the nodes being halted, the package will always be halted and not failover to another
node; the report will not display an assessment for that package.
node_name...
The name of the node(s) to halt.
RETURN VALUE
cmhaltnode returns the following value:
0 Successful completion.
1 Command failed.
EXAMPLES
Halt the cluster daemon on two other nodes:
cmhaltnode node2 node3
AUTHOR
cmhaltnode was developed by HP.
SEE ALSO
cmquerycl(1m), cmhaltcl(1m), cmruncl(1m), cmrunnode(1m), cmviewcl(1m), cmeval(1m).
Requires Optional Serviceguard Software cmhaltnode(1m)