It looks like you are using the chroot setup but loading named.conf from /etc.
You need to modify /etc/sysconfig/named to include the following directive
Code:
ROOTDIR=/var/named/chroot
After you have modified named.conf you should always test it using
Code:
service named testconfig
The ACL (Access Control List) errors are due to the fact that you are using "nms.example.com" in the listen-on and allow-query directives in the options statement. You cannot use FQDNs this way. You must do it something like this.
Hi all,
I am a beginner in DNS service and I face difficult when configure DNS sub domain using "bind" version 8. So I would like to ask a question about this and hope someone can answer my question.
Is it possible to configure a sub domain in which the name of this sub domain is same as a... (2 Replies)
i have the DNS and the web proxy services running on one of my sun machines....the funny thing is clients use the proxy server by addressing it with its IP address only....what i need is to assign it like...proxy.amu.edu.et......
my guess is the problem is the configuration with the DNS ...but i... (2 Replies)
I have a installed Redhat Linux v5 on a new HP Pavillon PC. It has a dual boot with Vista. Booting from Vista, I can connect to the internet. However with Redhat I cannot connect to the internet.
I looked at the /etc/resolv.conf file in Redhat and there is no DNS entry there. From where do I... (28 Replies)
I'm trying to configure DNS on a AIX 5.4 machine and I just can't figure it out. The IBM guide doesn't work. Smit also doesn't work. I have no idea how to make this happen. (2 Replies)
Hi All,
I have a list of few DNS server with hostnmae and IP which I need to setup in Solaris Servers...Can any one pls tell me the steps for setting up the above in solaris 10 & 9???? (4 Replies)
Dear members,
I am trying to set up a simple DNS but the problem is that when I ping the name of the IP address in the Reverse file, it does not recognise it. My code are as follows:
Note that my IP address is 172.22.45.237.
In my /etc/named.conf file, I have added the following lines
... (10 Replies)
Hello All,
I want to install ORACLE RAC on AIX 6.1.
In the installation guide. the below two points were mentioned:
Each node must have at least two network adapters or network interface cards
(NICs): one for the public network interface, and one for the private network
interface (the... (2 Replies)
Hello fellow unix dudes, I have a question on DNS.
Basically the error is my domain.com server can not send email to my
mail.domain.com server.
I have a virtual server with one IP say 192.10.11.12 and a mail server with
iP 172.4.5.6
When the virutal server on ip 192.10.11.12 was setup,... (0 Replies)
Hi all
m newbie in linux and trying to setup my internal DNS server for local network.After messing with DNS for hours i am posting this.
i have configured /etc/resolve.conf, hostname with domain name in /etc/sysconfig/network file,/etc/hosts file with local host entry and zone file... (1 Reply)
Discussion started by: Vaibhav.T
1 Replies
LEARN ABOUT CENTOS
ocf_heartbeat_xinetd
OCF_HEARTBEAT_XINETD(7) OCF resource agents OCF_HEARTBEAT_XINETD(7)NAME
ocf_heartbeat_Xinetd - Manages a service of Xinetd
SYNOPSIS
Xinetd [start | stop | status | monitor | meta-data | validate-all]
DESCRIPTION
Resource script for Xinetd. It starts/stops services managed by xinetd by enabling or disabling them in the configuration file.
The xinetd daemon itself must be running: we are not going to start or stop it ourselves.
All services should have a line saying either "disable=yes" or "disable=no". The script just changes those settings before reloading
xinetd.
Important: in case the services managed by the cluster are the only ones enabled, you should specify the -stayalive option for xinetd or it
will exit on Heartbeat stop. Alternatively, you may enable some internal service such as echo.
SUPPORTED PARAMETERS
service
The name of the service managed by xinetd.
(required, string, no default)
SUPPORTED ACTIONS
This resource agent supports the following actions (operations):
start
Starts the resource. Suggested minimum timeout: 20s.
stop
Stops the resource. Suggested minimum timeout: 20s.
restart
Suggested minimum timeout: 20s.
status
Performs a status check. Suggested minimum timeout: 10. Suggested interval: 10.
monitor
Performs a detailed status check. Suggested minimum timeout: 10. Suggested interval: 10.
validate-all
Performs a validation of the resource configuration. Suggested minimum timeout: 5.
meta-data
Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5.
EXAMPLE
The following is an example configuration for a Xinetd resource using the crm(8) shell:
primitive p_Xinetd ocf:heartbeat:Xinetd
params
service=string
op monitor depth="0" timeout="10" interval="10"
SEE ALSO
http://www.linux-ha.org/wiki/Xinetd_(resource_agent)
AUTHOR
Linux-HA contributors (see the resource agent source for information about individual authors)
resource-agents UNKNOWN 06/09/2014 OCF_HEARTBEAT_XINETD(7)