Hi Folks,
I've just installed solaris 8, but i cannot add my network card.
i've reboot the box, got into the configmode, and try'd to add a network card. but it doesn't work. I can't add a ip address to the card, an error occurs. Who do i add it.
Kind Regards (3 Replies)
Hello,
I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else.
- I dont have any /etc/hostnames.xxx
- ifconfig -a shows only the loopback
- kstat -c net shows only the loopback ...
Any... (11 Replies)
Installed solaris 10 and now i want to connect to internet,to make work this i need to NIC drivers can some body tell me is it possible to get drivers and how to install. I am dying to get rid of this problem..please help me (1 Reply)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Hi All,
does any body know how to create Virtual NIC in Solaris 10
if any one have good article or reference
kindly provide me
i try to Google
but i didn't find good one (7 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
hi guys,
is there any way to change the nic link_speed in Solaris 10? now my box is running degraded performance of the link speed as the switch is upgraded from 100m to 1000m.
dladm show-dev
e1000g0 link: up speed: 100 Mbps duplex: full
e1000g1 link: up ... (10 Replies)
Hi,
is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this.
Thanks®ards,
p (1 Reply)
Hi All
I would need to do hard code of nxge0 nic to full duplex & 1000mbps. So that whenever solaris server come up after reboot. it will show full duplex & 1000mbps setting only.
Please also let me know how to do it online through command.
regards (0 Replies)
Discussion started by: amity
0 Replies
LEARN ABOUT HPUX
xserver
Xserver(1) General Commands Manual Xserver(1)NAME
X - X Window System display server dispatcher
SYNOPSIS
X [ option ...]
DESCRIPTION :
Hewlett-Packard supports two X servers on HP-UX platforms, the Xhp X server which supports HP VISUALIZE graphics devices and the Xf86 X
server which supports all other graphics devices. These X servers are delivered as /usr/bin/X11/Xhp and /usr/bin/X11/Xf86.
The X dispatcher determines which X server to launch based on the available graphics devices. The control file /etc/X11/Xstart can provide
additional guidance to the X dispatcher. The control file allows the user to specify which X server to start for given display connection
numbers. The only X servers supported by the X dispatcher are Xhp, Xf86 and Xvfb. If no Xstart file exists, the dispatcher loads the
appropriate X server for the graphics device in the system. HP-UX does not deliver the /etc/X11/Xstart file. This file can be created by
using the SAM/SMH utility.
OPTIONS
If the X dispatcher is invoked with no arguments, the display connection is assumed to be :0. The X dispatcher checks for display connec-
tion options and, if found, uses that display connection number when it checks the Xstart file. All other options are passed on to the X
server when it is started and it is the X server's responsibility to validate these options. Not all options may be supported on both X
servers; refer to Xhp(1) and Xf86(1) to verify supported options for each X server.
RETURN VALUE
None
Xstart EXAMPLES
The control file syntax is the X server to start followed by the display connection number. Valid entries take the form of:
Xhp :0 Start the Xhp X server on display connection 0
Xf86 :10 Start the Xf86 X server on display 10
/usr/bin/X11/Xhp :5 Start the Xhp X server on display connection 5
/usr/bin/X11/Xvfb :7 Start the X Virtual Framebuffer server on display connection 7
FILES
/etc/X11/Xstart Dispatcher control file.
/var/X11/Xserver/logs/Xstartup.N.log X dispatcher log file for display N.
SEE ALSO X(1), Xhp(1), Xf86(1)STANDARDS CONFORMANCE
See the appropriate section in Xhp(1) or Xf86(1).
Xserver(1)