08-20-2009
AFAIK Etherchannel can be used for failover as well as link aggregation - if the switch supports it, as DukeNuke2 has said already. I haven't tried to use that in a HA-scenario, though.
I hope this helps.
bakunin
10 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
4. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
5. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
6. HP-UX
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Discussion started by: mkiron
1 Replies
7. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
8. Solaris
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Discussion started by: primeaup
3 Replies
9. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
10. Solaris
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
LEARN ABOUT CENTOS
postgresql-setup
POSTGRESQL-SETUP(1) Postgresql RPM-dist manual POSTGRESQL-SETUP(1)
NAME
postgresql-setup - manual page for postgresql-setup 9.2.7
SYNOPSIS
postgresql-setup {initdb|upgrade} [SERVICE_NAME]
DESCRIPTION
Script is aimed to help sysadmin with basic database cluster administration.
The SERVICE_NAME is used for selection of proper unit configuration file; For more info and howto/when use this script please look at the
docu file /usr/share/doc/postgresql-9.2.7/README.rpm-dist. The 'postgresql' string is used when no SERVICE_NAME is explicitly passed.
Available operation mode:
initdb Create a new PostgreSQL database cluster. This is usually the first action you perform after PostgreSQL server installation.
upgrade
Upgrade PostgreSQL database cluster to be usable with new server. Use this if you upgraded your PostgreSQL server to newer major
version (currently from 8.4 to 9.2).
ENVIRONMENT
PGSETUP_INITDB_OPTIONS
Options carried by this variable are passed to subsequent call of `initdb` binary (see man initdb(1)). This variable is used also
during 'upgrade' mode because the new cluster is actually re-initialized from the old one.
PGSETUP_PGUPGRADE_OPTIONS
Options in this variable are passed next to the subsequent call of `pg_upgrade`. For more info about possible options please look
at man pg_upgrade(1).
PGSETUP_DEBUG
Set to '1' if you want to see debugging output.
postgresql-setup 9.2.7 June 2014 POSTGRESQL-SETUP(1)