|
|
Sponsored Content
Operating Systems
Solaris
Move disks to different StorEdge, keeping RAID
Post 302344953 by alexs77 on Tuesday 18th of August 2009 05:14:05 AM
08-18-2009
Too fast.... :)
Quote:
Problem: Disks are in "new" SE3310. How to tell StorEdge, that those "new" disks (which it correctly identifies and displays as "USED DRV") make up a RAID5, which I could then map to a host (better: which I could then assign a LUN, after having "created" a RAID5 Logical Drive)?
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Sorry if this seems trivial. i have been given a task at work to configure a sun processing server "enterprise 4500" so it can work with the a storage server "storedge A5200" and "storedge D1000"
the truth is i have never worked on a sun server before. i need a guideline (step by step) as to... (5 Replies)
Discussion started by: lawalidowu
5 Replies
2. Solaris
Hello,
I have a d1000, it's connected to two servers, I want both servers to see all disks in the array. i.e. i have 6 disks, 3 in each side, I want both servers to see all 6 disks.
It appears to be setup in a split bus mode now, ive looked thru the manuals and have become confused!
So,... (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
3. Red Hat
We have a Red Hat linux server running on IBM x445 hardware. There are external disks in an IBM EXP300 disk enclosure. The system is running RAID 5. One of the four IBM disks (73.4 GB 10k FRU 06P5760) has become faulty. The system is still up and running OK because of the RAID. In that same EXP300... (3 Replies)
Discussion started by: pdudley
3 Replies
4. Solaris
HI guys.
Bit of a noob so bear with me.
I have 2 new disks I want to add to my StorEdge 3310 but am getting lost in the steps. We have another 3310 (JBOD) that I was able to plug the disks into and they instantly showed up. Did a few minor commands after (drvconfig, devfsadm etc..) and I was... (4 Replies)
Discussion started by: jamie_collins
4 Replies
5. Solaris
I've just installed Sol 10 Update 9 on a Sun 4140 server and have a RAID 1 configuration (2 136 Gb drives) for the OS and have created a RAID 5 array (6 136 GB) drives. When i log into the system I am unable to see the RAID 5 disks at all. I've tried using the devfsadm command but no luck and... (9 Replies)
Discussion started by: goose25
9 Replies
6. Linux
hello
my centOS newly installed system loading dmraid modules on startup
I did remove all LVM/raid things from system installation menus and after installation too but dmraid is still there
and he says: no raid disks found
also I did modprobe -r dm_raid45 and it do remove it but only until... (7 Replies)
Discussion started by: tip78
7 Replies
7. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
8. Solaris
Hey everyone. First, let me start by saying I'm primarily focused on linux boxes, and just happened to get pulled into building two T5220's. I'm not super educated on sun boxes.
Both T5220's have 8 146GB 15k SAS drives. Inside the service processor, I can run SHOW /SYS/HDD{0-7} and they all come... (2 Replies)
Discussion started by: msarro
2 Replies
9. Solaris
Dear All ,
Pl find the below command ,
# raidctl -l
Controller: 1
Volume:c1t0d0
Disk: 0.0.0
Disk: 0.1.0
Disk: 0.3.0
#
raidctl -l c1t0d0
Volume Size Stripe Status Cache RAID
Sub Size ... (10 Replies)
Discussion started by: jegaraman
10 Replies
10. Shell Programming and Scripting
The below will move all the files in the directory dir to the destination using parallel and create a log, however will not keep them in the directory. I have tried mkdir -p but that does not seem to work or at least I can not seem to get it (as it deletes others files when I use it). What is the... (2 Replies)
Discussion started by: cmccabe
2 Replies
LEARN ABOUT V7
yppoll
yppoll(1M) System Administration Commands yppoll(1M) NAME
yppoll - return current version of a NIS map at a NIS server host SYNOPSIS
/usr/sbin/yppoll [-d ypdomain] [-h host] mapname DESCRIPTION
The yppoll command asks a ypserv() process what the order number is, and which host is the master NIS server for the named map. OPTIONS
-d ypdomain Use ypdomain instead of the default domain. -h host Ask the ypserv process at host about the map parameters. If host is not specified, the NIS server for the local host is used. That is, the default host is the one returned by ypwhich(1). ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWnisu | +-----------------------------+-----------------------------+ SEE ALSO
ypwhich(1), ypfiles(4), attributes(5) SunOS 5.10 14 Sep 1992 yppoll(1M)