08-14-2009
Hi Cer,
Thanks a lot for getting back on this ...
We have setup where we need to move the standalones to LPARs and in this case we need to make sure that we have cleared the LUN reservation on the source server and then later import the vgs which will be on target.
So was jst curious to knw what wud be the case if LUN reserveration is not cleared.
Regards,
nivas
8 More Discussions You Might Find Interesting
1. Solaris
I have a list of LUN ID, my task is to find if disk has been added or not. How do I do that? I have been searching the forum and not able to find answer.
thanks (4 Replies)
Discussion started by: uuontario
4 Replies
2. AIX
Hello all,
I have the following env:
* DS4300 storage SAN
* AIX 5.3 Lpar (storage through vio server)
* AIX 5.3 Server
Some FS are too small do I'm setting up a process to increase the size of the FS.
To expand the size of the FS I plan to do the following for the physical AIX server,... (1 Reply)
Discussion started by: petervg
1 Replies
3. Red Hat
Hi,
Is there command to detect the newly added LUN is linux box. I tried with below commands, but that doesn't work out.
fdisk -l,
fdisk -l | grep Disk
pvscan (5 Replies)
Discussion started by: gsiva
5 Replies
4. AIX
Hi,
I am not getiting lun id information on VIO Server. I have used the command fget_config command.
just showing # prompt.
I would like know wheather any other command is there equiv of fget_config
which will display lun id? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
5. Solaris
Dear all,
i want to get the LUN ID for some disks in solaris 10
what commands options for the MPXIO and inq i want these utilities only
because i don't have solution enabler or powerpath
BR, (1 Reply)
Discussion started by: maxim42
1 Replies
6. Solaris
Hi All,
I am a RH Linux admin that recently started working at a company with a number of SUN Servers so it's been an interesting transition.
Considering the last person left with very little documentation left behind so I have been picking up most issues half complete, or troubleshot.
... (7 Replies)
Discussion started by: MobileGSP
7 Replies
7. HP-UX
Hi guys,
I need some help to better understand how to determine if a disk have persistent SCSI reservation. I know that we should use the "Persisten Reservation Utility" but we are not allowed to run that tool. Since we have the output from some grab utility and specifically we have the... (0 Replies)
Discussion started by: cecco16
0 Replies
8. Solaris
Hi
I am having two node cluster. I was trying to change the to use scsi3 reservation for all disks having two paths. Please let me know where I went wrong or there any issue to implement the same.
On node1
bash-3.2# cldev status
=== Cluster DID Devices ===
Device Instance ... (8 Replies)
Discussion started by: sb200
8 Replies
LEARN ABOUT DEBIAN
ql-dynamic-tgt-lun-disc
ql-dynamic-tgt-disc(8) System Administration ql-dynamic-tgt-disc(8)
NAME
ql-dynamic-tgt-lun-disc - Scans for newly added LUNs.
SYNOPSIS
ql-dynamic-tgt-lun-disc [OPTIONS]
DESCRIPTION
Dynamic TGT-LUN Discovery Utility
This utility scans for newly added LUNs. After adding new LUNs, you do not need to unload, then load the QLogic FC driver or reboot the
system
To begin scanning the LUNs issue following command:
# /usr/sbin/ql-dynamic-tgt-lun-disc
-al, --allow-lip
LIP is not issued by default, even if it is required for scanning new LUNs Setting this option, allows the utility to issue LIP.
-cl, --current-luns
Displays LUNS currently present
-e, --extended-scan
Use this option as "-e | --extended-scan". to rescan LUNs. This will identify any change in attributes of existing LUNs. This option
can be used in combination of scan/refresh or max luns
-h, --help, ?
Prints this help message
-i, --interactive
Use this option to use the menu driven program
-is, --iscsi
Use this option to operate on ISCSI HBAs, this option can be used in combination of any other supported option.
-m, --max-lun
To set the maximum LUNs to be scanned
-p, --proc
Use PROC file system for LUN scanning
-r, --refresh
To refresh, that is remove LUNs that are lost use the options "-r|--refresh". This will remove the LUNs which no more exist.
-s, --scan [ -r|--refresh ]
The QLogic LUN scan utility re-scans all the devices connected to the QLogic HBA
SEE ALSO
ql-lun-state-online(8), ql-hba-snapshot(8), ql-set-cmd-timeout(8)
Matthias Schmitz <matthias@sigxcpu.org> July 2009 ql-dynamic-tgt-disc(8)