08-14-2009
Hi Cer,
Thanks a lot for getting back on this ...
We have setup where we need to move the standalones to LPARs and in this case we need to make sure that we have cleared the LUN reservation on the source server and then later import the vgs which will be on target.
So was jst curious to knw what wud be the case if LUN reserveration is not cleared.
Regards,
nivas
8 More Discussions You Might Find Interesting
1. Solaris
I have a list of LUN ID, my task is to find if disk has been added or not. How do I do that? I have been searching the forum and not able to find answer.
thanks (4 Replies)
Discussion started by: uuontario
4 Replies
2. AIX
Hello all,
I have the following env:
* DS4300 storage SAN
* AIX 5.3 Lpar (storage through vio server)
* AIX 5.3 Server
Some FS are too small do I'm setting up a process to increase the size of the FS.
To expand the size of the FS I plan to do the following for the physical AIX server,... (1 Reply)
Discussion started by: petervg
1 Replies
3. Red Hat
Hi,
Is there command to detect the newly added LUN is linux box. I tried with below commands, but that doesn't work out.
fdisk -l,
fdisk -l | grep Disk
pvscan (5 Replies)
Discussion started by: gsiva
5 Replies
4. AIX
Hi,
I am not getiting lun id information on VIO Server. I have used the command fget_config command.
just showing # prompt.
I would like know wheather any other command is there equiv of fget_config
which will display lun id? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
5. Solaris
Dear all,
i want to get the LUN ID for some disks in solaris 10
what commands options for the MPXIO and inq i want these utilities only
because i don't have solution enabler or powerpath
BR, (1 Reply)
Discussion started by: maxim42
1 Replies
6. Solaris
Hi All,
I am a RH Linux admin that recently started working at a company with a number of SUN Servers so it's been an interesting transition.
Considering the last person left with very little documentation left behind so I have been picking up most issues half complete, or troubleshot.
... (7 Replies)
Discussion started by: MobileGSP
7 Replies
7. HP-UX
Hi guys,
I need some help to better understand how to determine if a disk have persistent SCSI reservation. I know that we should use the "Persisten Reservation Utility" but we are not allowed to run that tool. Since we have the output from some grab utility and specifically we have the... (0 Replies)
Discussion started by: cecco16
0 Replies
8. Solaris
Hi
I am having two node cluster. I was trying to change the to use scsi3 reservation for all disks having two paths. Please let me know where I went wrong or there any issue to implement the same.
On node1
bash-3.2# cldev status
=== Cluster DID Devices ===
Device Instance ... (8 Replies)
Discussion started by: sb200
8 Replies
LEARN ABOUT DEBIAN
sg_emc_trespass
SG_EMC_TRESPASS(8) SG3_UTILS SG_EMC_TRESPASS(8)
NAME
sg_emc_trespass - Changes ownership of a LUN from another Service-Processor to this one.
SYNOPSIS
sg_emc_trespass [-d] [-hr] [-s] [-V] DEVICE
DESCRIPTION
sg_emc_trespass sends an EMC-specific Trespass Command to the DEVICE with the selected options. This Mode Select changes the ownership of
the LUN of the device from another Service-Processor to the one the command was received on.
OPTIONS
Arguments to long options are mandatory for short options as well.
-d outputs some extra debug information associated with executing this command
-hr Sets the 'Honor Reservation' bit in the command. If set, the trespass will only succeed to change the ownership from the Peer SP if
the Peer SP does not have an outstanding SCSI reservation for the LUN. By default, the reservation state will be ignored.
-s Send the short version of the trespass command instead of the long version. The short version is supported on the EMC FC5300, FC4500
and FC4700. The long version (default) is supported on the CLARiiON CX and AX family arrays.
-V print out version string then exit.
In the 2.4 series of Linux kernels the DEVICE must be a SCSI generic (sg) device. In the 2.6 series block devices (e.g. SCSI disks and DVD
drives) can also be specified. For example "sg_start 0 /dev/sda" will work in the 2.6 series kernels.
EXIT STATUS
The exit status of sg_emc_trespass is 0 when it is successful. Otherwise see the sg3_utils(8) man page.
AUTHOR
Written by Lars Marowsky-Bree, based on sg_start.
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright (C) 2004 Lars Marowsky-Bree, Douglas Gilbert.
This software is distributed under the GPL version 2. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
POSE.
sg3_utils-1.23 January 2007 SG_EMC_TRESPASS(8)