Hi everyone,
I have text files that I want to delete lines from. I have searched through this forum for quite some time and found examples of both awk and sed. Unfortunately, I was not able to successfully do what I want. Well to some extent. I did manage to delete the first 15 lines from each... (5 Replies)
Hi,
I would like to know how can I get to a new file, some lines from an existing file. Like, I want to get the lines between 100 and 150.
Best regards. (1 Reply)
I am attempting to insert multiple lines of text into a specific place in a text file based on the lines above or below it.
For example, Here is a portion of a zone file.
IN NS ns1.domain.tld.
IN NS ns2.domain.tld.
IN ... (2 Replies)
I would like to use grep to select multiple lines from a text file using a single-column text file. Basically I want to only select lines from the first text file where the second column of the first text file matches the second text file. How do I go about doing that? Thanks! (5 Replies)
Hi,
I am trying to extract lines from a text file given a text file containing line numbers to be extracted from the first file. How do I go about doing this? Thanks! (1 Reply)
I have 2 TXT files with with 8 columns in them(tab separated). First file has 2000 entries whereas 2nd file has 300 entries.
The first file has ALL the lines of second file. Now I need to remove those 300 lines (which are in both files) from first file so that first file's line count become... (2 Replies)
Is there any work around to get no. lines in a text file and cut by total of 2 lines per file or whatever input parameter of command.
so for ei. this file
cat file1
1
2
3
4
5
6
7
filename output is incremental look like this:
linefile.txt
1_linefile.txt
2_linefile.txt... (4 Replies)
I dont even have a sample script cause I dont know where to start from. My data lookes like this
> sat#16 #data: 15 site:UNZA baseline: 205.9151
0.008 -165.2465 35.8109 40.6685 21.9148 121.1446 26.4629 -18.4976 33.8722
0.017 -165.2243 48.2201 40.6908 ... (8 Replies)
Hello All,
this is my first post so I don't know if I am doing this right.
I would like to append entries from a series of strings (contained in a text file) consecutively at the end of specifically labeled lines in another file.
As an example:
- the file that contains the values to be... (3 Replies)
hi all,
trying this using shell/bash with sed/awk/grep
I have two files, one containing one column, the other containing multiple columns (comma delimited).
file1.txt
abc12345
def12345
ghi54321
...
file2.txt
abc1,text1,texta
abc,text2,textb
def123,text3,textc
gh,text4,textd... (6 Replies)
Discussion started by: shogun1970
6 Replies
LEARN ABOUT HPUX
fold
fold(1) General Commands Manual fold(1)NAME
fold - fold long lines for finite width output device
SYNOPSIS
width] [file ...]
Obsolete form:
width] [file ...]
DESCRIPTION
The command is a filter that folds the contents of the specified files, breaking the lines to have a maximum of width column positions (or
bytes, if the option is specified). The command breaks lines by inserting a newline character so that each output line is the maximum
width possible that does not exceed the specified number of column positions (or bytes). A line cannot be broken in the middle of a char-
acter. If no files are specified or if a file name of is specified, the standard input is used.
The command is often used to send text files to line printers that truncate, rather than fold, lines wider than the printer is able to
print.
If the backspace, tab, or carriage-return characters are encountered in the input, and the option is not specified, they are treated spe-
cially as follows:
Backspace The current count of line width is decremented by one, although the count never becomes negative. Thus, the char-
acter sequence character-backspace-character counts as using one column position, assuming both characters each
occupy a single column position. does not insert a newline character immediately before or after any backspace
character.
Tab Each tab character encountered advances the column position pointer to the next tab stop. Tab stops are set 8 col-
umns apart at column positions 1, 9, 17, 25, 33, etc.
Carriage-return The current count of line width is set to zero. does not insert a newline character immediately before or after
any carriage-return character.
Note that may affect any underlining that is present.
Options
The command recognizes the following options and command-line arguments:
Count width in bytes rather than in column positions.
Break the line on the last blank character found
before the specified number of column positions (or bytes). If none are found, break the line at the specified
line length.
Specify the maximum line length, in column positions (or bytes if
is specified). The default value is 80. width should be a multiple of 8 if tabs are present, or the tabs should
be expanded using before processing by (see expand(1)). The option is obsolescent and may be removed in a future
release.
EXTERNAL INFLUENCES
Environment Variables
determines the interpretation of text as single- and/or multi-byte characters.
determines the language in which messages are displayed.
If or is not specified in the environment or is set to the empty string, the value of is used as a default for each unspecified or empty
variable. If is not specified or is set to the empty string, a default of "C" (see lang(5)) is used instead of
If any internationalization variable contains an invalid setting, behaves as if all internationalization variables are set to "C". See
environ(5).
International Code Set Support
Single- and multi-byte character code sets are supported.
SEE ALSO expand(1).
STANDARDS CONFORMANCE fold(1)