You absolutely need to edit this file for SAN devices unless you have a tool that does it for you. Solaris will not search for LUN's that are not listed in this file.
The following will search the first 4 SAN devices it finds for LUN ID's 0, 1 and 2:
HI,
I want a help for Configuring snmpd.conf and snmptrapd.conf (i.e Configuring SNMP)
for receiving
TRAPS in my networks. I am using RHEL4.0 OS.
Please tell me How I can configure above two files in a proper way and at an
advanced level.
Especially I am getting... (2 Replies)
Folks;
I know this might sounds stupid, but please help with this:
I have share in my smb.conf on my SUSE 10 box.
How can i make this share accessible to outside IP range or a specific IP address without need for user/pass?
Here's the share as it's written in smb.conf:
;
;comment =... (0 Replies)
Hey all!
I'm working on Solaris10 right now and I was fiddling around with a fresh install and was wondering about the service that uses resolv.conf?
I know prior to Sol10 (SMF) it was /etc/init.d/inetsvc stop and start to reload resolv.conf changes
but I can't seem to find the correct SMF... (5 Replies)
OK I am running solaris 10.
I made some changes to my ipf.conf file and issued the command:
ipf -Fa -f /etc/ipf/ipf.conf
to flush out the old and bring in the new changes.
When I ran ipfstat -ioh to verify it had brought in the new rule set I saw something I wasn't expecting to see.
I... (3 Replies)
Hi,
I have a question on /etc/syslog.conf file in Solaris 10.
Below is a line taken from /etc/syslog.conf file and I know that the last field (operator) is where the logs gets outputted but how do I find out what the output file name format is going to be and which directory it gets outputted... (1 Reply)
i have this program running on my solaris and there are two identical config files, i am not sure which one is being used by this program but I am sure it uses one of them.
I run lsof -p {pid} but it does not show which config file has been read by this program, what i am doing wrong?
thanks (4 Replies)
Hi,
I was told to add the "nis" in front of "files" for below lines in /etc/nsswitch.conf was not in a good practise. I tried to search in google and man page for nsswitch.conf and can't find the answer. could someone please help me?
passwd: nis files
shadow: nis files
group: nis files... (2 Replies)
Hello all,
Newbie here.
I'm currently tasked with updating rsyslog.conf and auditd.conf on a large set of servers. I know the exact logging configurations that I want to enable. I have updated both files on on a server and hope to use the updated files as a template for the rest of the... (3 Replies)
Hi,
I've installed Solaris 11.3(live media) and configured DNS. Everytime I reboot the server, resolv.conf got deleted and it created a new nsswitch.conf.
I used below to configure both settings:
# svccfg -s dns/client
svc:/network/dns/client> setprop config/nameserver = (xx.xx.xx.aa... (1 Reply)
Discussion started by: flexihopper18
1 Replies
LEARN ABOUT SUSE
tgt-setup-lun
tgt-setup-lun(8) System Manager's Manual tgt-setup-lun(8)NAME
tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target
SYNOPSIS
tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h]
DESCRIPTION
Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows:
iqn.2001-04.com.<hostname>-<target_name> The target name must be unique.
The script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia-
tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator.
EXAMPLES
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82
Create a target that uses /dev/sdb1 and allows connections from any initiator:
tgt-setup-lun -d /dev/sdb1 -n my_target
Display help:
tgt-setup-lun -h
AUTHOR
Written by Erez Zilber
REPORTING BUGS
Report bugs to <erezz@voltaire.com>.
COPYRIGHT
Copyright (C) Voltaire Ltd. 2008.
tgt-setup-lun(8)