|
|
Sponsored Content
Operating Systems
Solaris
solaris 10 u5 what happens if no default route configured
Post 302340260 by prym_admin on Monday 3rd of August 2009 06:02:27 AM
08-03-2009
|
|
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Dear Friends, I'm here again
I need to know where is the permanent file for gateway configuration.
I did the following command
route add -net 0.0.0.0 5.0.0.3 ( My Gateway), but when i restart my computer i have to do it again.
What the file can i set the permanent configuration for my... (1 Reply)
Discussion started by: themask
1 Replies
2. Solaris
I am having problems getting this to work, though it seems like it would be simple. I have a host with 2 interfaces, hme0 (192.168.0.132) for the primary interface, and hme1 (192.168.0.16) for backups. I want it to talk to the backup host, which is 192.168.0.21, across the hme1 interface.
Thanks (2 Replies)
Discussion started by: 98_1LE
2 Replies
3. Solaris
hi,
i installed solaris 9 on an SPARC server with two network interfaces. behind each interface is a small lan. i can reach every computer in every lan using one of the other interface when i am logged in the solaris. but if a computer from one lan has to connect to a computer on the other lan,... (4 Replies)
Discussion started by: bong02
4 Replies
4. Solaris
Hi,
Any one can help me in this below mentioned issue I am facing in my solaris server?
here the scenario goes....
i have multiple segments in my LAN like remote csr, database, production etc. and all the segments are configured in Windows/CISCo network.
from my all system in remote... (1 Reply)
Discussion started by: Praan
1 Replies
5. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
6. Solaris
Hiya,
I got the default gateway set in /etc/defaultrouter file, however "netstat -nr" doesn't show anything like "default" in the routing table. As far as I know "netstat" on Solaris 10 u7 should show something like :
Routing Table: IPv4
Destination Gateway Flags Ref ... (8 Replies)
Discussion started by: TomSu
8 Replies
7. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
8. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
9. Solaris
Hi
We took the reboot of server/global zone after that Solaris 11 share local zone not able to ping the default gateway but global zone able to ping same default gateway. I check/compare the before activity logs of global zone and local zones which looks fine to me, further IP and netmask of... (6 Replies)
Discussion started by: sb200
6 Replies
LEARN ABOUT SUNOS
install-solaris
install-solaris(1M) install-solaris(1M) NAME
install-solaris - install the Solaris operating system SYNOPSIS
install-solaris install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation, install-solaris invokes either a text-based installer or a graphical installer. The following minimum requirements for physical memory dictate which features are available during installation: For SPARC machines: 128 MB Minimum physical memory for all installation types 128 MB Minimum physical memory required for windowing system 384 MB Minimum physical memory required for graphical-based installation For x86 machines: 256 MB Minimum physical memory for all installation types 256 MB Minimum physical memory required for windowing system 512 MB Minimum physical memory required for graphical-based installation In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea- tures available. install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more details. install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the installation media. Refer to the for disk space requirements. Refer to the for more information on the various menus and selections. See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcdrom (Solaris instal- | | |lation media) | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ pkginfo(1), install(1M), pkgadd(1M), attributes(5) It is advisable to exit install-solaris by means of the exit options in the install-solaris menus. 23 Sep 2005 install-solaris(1M)