08-03-2009
solaris 10 u5 what happens if no default route configured
Hi,
I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another server on the network?
If no default route configured does it do a broadcast ping on the network and pick a gateway that way? There can be multiple default routes, how is a default route choosen in that case, on a round robin basis?
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Dear Friends, I'm here again
I need to know where is the permanent file for gateway configuration.
I did the following command
route add -net 0.0.0.0 5.0.0.3 ( My Gateway), but when i restart my computer i have to do it again.
What the file can i set the permanent configuration for my... (1 Reply)
Discussion started by: themask
1 Replies
2. Solaris
I am having problems getting this to work, though it seems like it would be simple. I have a host with 2 interfaces, hme0 (192.168.0.132) for the primary interface, and hme1 (192.168.0.16) for backups. I want it to talk to the backup host, which is 192.168.0.21, across the hme1 interface.
Thanks (2 Replies)
Discussion started by: 98_1LE
2 Replies
3. Solaris
hi,
i installed solaris 9 on an SPARC server with two network interfaces. behind each interface is a small lan. i can reach every computer in every lan using one of the other interface when i am logged in the solaris. but if a computer from one lan has to connect to a computer on the other lan,... (4 Replies)
Discussion started by: bong02
4 Replies
4. Solaris
Hi,
Any one can help me in this below mentioned issue I am facing in my solaris server?
here the scenario goes....
i have multiple segments in my LAN like remote csr, database, production etc. and all the segments are configured in Windows/CISCo network.
from my all system in remote... (1 Reply)
Discussion started by: Praan
1 Replies
5. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
6. Solaris
Hiya,
I got the default gateway set in /etc/defaultrouter file, however "netstat -nr" doesn't show anything like "default" in the routing table. As far as I know "netstat" on Solaris 10 u7 should show something like :
Routing Table: IPv4
Destination Gateway Flags Ref ... (8 Replies)
Discussion started by: TomSu
8 Replies
7. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
8. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
9. Solaris
Hi
We took the reboot of server/global zone after that Solaris 11 share local zone not able to ping the default gateway but global zone able to ping same default gateway. I check/compare the before activity logs of global zone and local zones which looks fine to me, further IP and netmask of... (6 Replies)
Discussion started by: sb200
6 Replies
LEARN ABOUT DEBIAN
make_sockdfr
MAKE_SOCKDFR(8) System Manager's Manual MAKE_SOCKDFR(8)
NAME
make_sockdfr - Generates frozen route file for SOCKS server
SYNOPSIS
make_sockdfr [infile [outfile] ]
DESCRIPTION
make_sockdfr reads in a plain-text route file for the SOCKS server and produces a frozen route file as the output.
Both arguments are optional. The default for infile is /etc/sockd.route; the default for outfile is /etc/sockd.fr. You may specify infile
while omitting outfile, but you cannot specify outfile without also speficying infile.
The contents of the frozen route file is essentially the memory image of the parsed input file. Using the frozen route file can reduce the
start-up delay of the SOCKS server program since it no longer has to parse the file contents.
When the SOCKS server starts, it always looks for the frozen route file /etc/sockd.fr first. If that file is not found, it then tries to
use the plain-text route file /etc/sockd.route. If you use frozen route file, you must remember to run make_sockdfr every time after you
modify the plain-text file or the SOCKS server will continue to use the frozen version of a previous route file.
To find out the contents of a frozen route file, use dump_sockdfr.
FILES
/etc/sockd.fr, /etc/sockd.route
SEE ALSO
dump_sockdfr(8), sockd.fr(5), sockd.route(5)
AUTHOR
Ying-Da Lee, yingda@esd.sgi.com or yingda@best.com
May 6, 1996 MAKE_SOCKDFR(8)