07-30-2009
svcadm clear ftp
svcadm disable ftp
10 More Discussions You Might Find Interesting
1. Solaris
I had a power failure the other day and when my relatively new Solaris 10 machine rebooted it is thrown into maintenance mode.
I've found the following lines in the /var/adm/messages file, I'm assuming this is the root cause of the problem. However, I don't have the slightest idea on how to... (9 Replies)
Discussion started by: cheetobandito
9 Replies
2. Solaris
Hi,
I have installed Hudson on a Solaris 11 server, using the installation instructions available at Paul Oswald: Hudson Solaris SMF Manifest.
When I perform svcs -l hudson, I get:
fmri svc:/application/hudson:default
name Hudson Continuous Build Server
enabled true... (4 Replies)
Discussion started by: JVerstry
4 Replies
3. Solaris
I have a Solaris 10 SunFire v880 machine and I'm having trouble with Samba.
Samba has worked on this machine but since the machine has been re-booted Samba has not worked.
Machine details are:
cat /etc/release
Solaris 10 10/08 s10s_u6wos_07b SPARC
Copyright 2008... (2 Replies)
Discussion started by: KenLynch
2 Replies
4. Solaris
Hi Guys,
I have a sunblade 1500. I booted the system and it booted to maintenance mode. How can I fix this?
Thanks lots (8 Replies)
Discussion started by: cjashu
8 Replies
5. Solaris
I have seen similar threads on this issue, but I have not seen a fix. Basically I am getting a lot of rcp bind errors. Below find the output of "svcs -xv". not sure where to begin:
# svcs -xv
svc:/network/rpc/bind:default (RPC bindings)
State: maintenance since Fri May 25 14:13:18 2012... (14 Replies)
Discussion started by: brownwrap
14 Replies
6. Solaris
:confused:
when i tried to look the status of DNS-client, it is in maintenance mode.....
Please tell me how to bring it back to online mode...PLEASE TELL ME STEP BY STEP.... PLEASE...
:wall: (2 Replies)
Discussion started by: vamshigvk475
2 Replies
7. Solaris
Hi,
I have an issue with RPC bind service and its failing with status 1. any help would be much appreciated.
THanks (2 Replies)
Discussion started by: Yakub Humami
2 Replies
8. Solaris
All I'm running an OpenSolaris system (Nexenta). When doing a svcs I see that/network/smb/server is in maintenance mode.
I have run a clear on the service and restarted. I see the same service show online* for a bit but then, enters maintenance every time.
In the service log I... (2 Replies)
Discussion started by: dcpatriot
2 Replies
9. AIX
Hi this may be a easy question to answer but thanks in advance.
So I was able to download the VIOS media from IBM and currently I am burning it to a cd/dvd right now.
The steps I've collected so far are from the net. can you please confirm and add on to the steps if there are any steps... (0 Replies)
Discussion started by: Adnans2k
0 Replies
10. Solaris
i booted into maintenance mode
boot -- -s
from the console
I got the
Root password for system maintenance (control-d to bypass)
I did control -d
and then logged in
it told me that I was booting into boot -s
but after I did a control -d and logged in
who -r shows
... (9 Replies)
Discussion started by: goya
9 Replies
LEARN ABOUT OPENSOLARIS
sulogin
sulogin(1M) System Administration Commands sulogin(1M)
NAME
sulogin - access single-user mode
SYNOPSIS
sulogin
DESCRIPTION
The sulogin utility is automatically invoked by init when the system is first started. It prompts the user to type a user name and password
to enter system maintenance mode (single-user mode) or to type EOF (typically CTRL-D) for normal startup (multi-user mode). The user should
never directly invoke sulogin. The user must have the solaris.system.maintenance authorization.
The sulogin utility can prompt the user to enter the root password on a variable number of serial console devices, in addition to the tra-
ditional console device. See consadm(1M) and msglog(7D) for a description of how to configure a serial device to display the single-user
login prompt.
FILES
/etc/default/sulogin
Default value can be set for the following flag:
PASSREQ
Determines if login requires a password. Default is PASSREQ=YES.
/etc/default/login
Default value can be set for the following flag:
SLEEPTIME
If present, sets the number of seconds to wait before login failure is printed to the screen and another login attempt is allowed.
Default is 4 seconds. Minimum is 0 seconds. Maximum is 5 seconds.
Both su(1M) and login(1) are affected by the value of SLEEPTIME.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsr |
+-----------------------------+-----------------------------+
SEE ALSO
auths(1), login(1), consadm(1M), init(1M), su(1M), attributes(5), msglog(7D)
NOTES
By default, the root user has all authorizations.
Granting the solaris.system.maintenance authorization to the Console User Rights Profile may have an undesirable side effect of granting
the currently logged in user maintenance mode access. The solaris.system.maintenance authorization should be directly granted to appropri-
ate users rather than through the Console User Rights Profile.
SunOS 5.11 21 Aug 2008 sulogin(1M)