Sponsored Content
Operating Systems Solaris ping -s to default gateway very slow Post 302337939 by reborg on Sunday 26th of July 2009 11:11:51 AM
Old 07-26-2009
Can you verify your netmask, dns and speed/duplex settings ?

Also check "dmesg" for errors/warnings when the ping -s is running.
 

10 More Discussions You Might Find Interesting

1. IP Networking

Unable to ping the gateway IP itself

We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command 64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies

2. IP Networking

Multihomed can not ping gateway

Hello this is my first post at this forum. Apologize for my lack of network understanding but Im posting to learn. I have a problem reaching default gateway 10.18.110.1 If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping. cat... (11 Replies)
Discussion started by: vettec3
11 Replies

3. AIX

Can not Ping Gateway

Hello, I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies

4. Red Hat

Cannot ping gateway

I know the subject line is very similar to: destination host unreachable but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there. We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies

5. UNIX for Dummies Questions & Answers

Cannot ping default gateway

I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies

6. AIX

Cant ping default gateway aix 53 07 new install

I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a startsrc -g tcpip ... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies

7. Red Hat

Can not ping default gateway

Hi, Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies

8. AIX

Networking Issue (Cant Ping the gateway)

Hi, I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure? Is there anything that I have to check with vio setting or Am I missing any configuration? Please let me know further. Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies

9. UNIX for Advanced & Expert Users

Unable to ping default gateway

I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos) # ifconfig enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies

10. UNIX for Beginners Questions & Answers

Inconsistency between RedHat 6.5 global gateway and single gateway leads to loss of default gateway

Dear friends I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
sg_get_network_iface_stats(3)				     Library Functions Manual				     sg_get_network_iface_stats(3)

NAME
sg_get_network_iface_stats - get network interface statistics SYNOPSIS
#include <statgrab.h> sg_network_iface_stats *sg_get_network_iface_stats(int *entries); DESCRIPTION
The sg_get_network_iface_stats function takes a pointer to an int, entries, which is filled with the number of network interfaces the machine has. This is needed to know how many sg_network_iface_stats structures have been returned. A pointer is returned to the first sg_network_iface_stats. sg_get_network_iface_stats returns statistics about the network interfaces in the machine. Specifically, it returns the speed of the inter- face, the duplex state, and whether it is currently up. RETURN VALUES
The sg_get_network_iface_stats returns a pointer to a structure of type sg_network_iface_stats. typedef enum{ SG_IFACE_DUPLEX_FULL, SG_IFACE_DUPLEX_HALF, SG_IFACE_DUPLEX_UNKNOWN }sg_iface_duplex; Note: The SG_IFACE_DUPLEX_UNKNOWN value could mean that duplex hasn't been negotiated yet. typedef struct{ char *interface_name; int speed; sg_iface_duplex duplex; int up; }sg_network_iface_stats; interface_name The name known to the operating system. (eg. on linux it might be eth0) speed The speed of the interface, in megabits/sec. duplex The duplex state the interface is in. See sg_iface_duplex for permitted values. up Whether the interface is up. SEE ALSO
statgrab(3) WEBSITE
http://www.i-scream.org/libstatgrab/ i-scream $Date: 2005/07/13 09:31:53 $ sg_get_network_iface_stats(3)
All times are GMT -4. The time now is 05:23 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy