07-20-2009
Need some link or help as how to start
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hello,
Under ksh I have to run a script on one of the nodes of a Solaris 8 cluster which at some time must execute a command on the alternate node:
# rsh <name> "command"
I have to implement this script on all the clusters of my company (a lot of...).
Fortunately, the names of the two nodes... (11 Replies)
Discussion started by: heartwork
11 Replies
2. HP-UX
Need help guys!
when running cmrunnode batch i'm getting this error
cmrunnode : Waiting for cluster to... (1 Reply)
Discussion started by: Tris
1 Replies
3. HP-UX
Hi,
Please advise me whereas I have two node cluster server configured with MC/SG. Application and DB are running on Node 1, while Node 2 is standby.
All the volume group devices are part of cluster environment. There is only one package running at node 1.
Node 2 is having the problem to... (1 Reply)
Discussion started by: rauphelhunter
1 Replies
4. High Performance Computing
hi,
i am trying to setup a 2 node cluster environment. following is what i have;
1. 2 x sun ultra60 - 450MHz procs, 1GB RAM, 9GB HDD, solaris 10
2. 2 x HBA cards
3. 2 x Connection leads to connect ultra60 with D1000
4. 1 x D1000 storage box.
5. 3 x 9GB HDD + 2 x 36GB HDD
first of all,... (1 Reply)
Discussion started by: solman17
1 Replies
5. Solaris
I now the logical name and Virtual IP of the cluster.
How can I find the active sun cluster node without having root access? (3 Replies)
Discussion started by: sreeniatbp
3 Replies
6. HP-UX
Hello,
Is there any way to identify the active node in a HP-UX cluster without root privileges? (3 Replies)
Discussion started by: psimoes79
3 Replies
7. Solaris
Hi Gurus,
I am very new to clustering and for test i have created a single node cluster, now i want to remove the system from cluster. Did some googling however as a newbee in cluster unable to co related the info.
Please help
Thanks (1 Reply)
Discussion started by: kumarmani
1 Replies
8. Solaris
How can we add a shared zfs dataset between 2 zones on a same host. I have sun cluster 3.2 installed in a server which has 2 zones. I want to share a zfs data set between these 2 zones how can we do that ? (7 Replies)
Discussion started by: fugitive
7 Replies
9. Solaris
Hi,
Is it possible to have a Solaris cluster of 2 nodes at SITE-A using SVM and creating metaset using say 2 LUNs (on SAN). Then replicating these 2 LUNs to remote site SITE-B via storage based replication and then using these LUNs by importing them as a metaset on a server at SITE-B which is... (0 Replies)
Discussion started by: dn2011
0 Replies
10. AIX
Setting up HACMP 6.1 on a two node cluster. The other node works fine and can start properly on STABLE state (VGs varied, FS mounted, Service IP aliased). However, the other node is always stuck on ST_JOINING state. Its taking forever and you can't stop the cluster as well or recover from script... (2 Replies)
Discussion started by: depam
2 Replies
link(1) General Commands Manual link(1)
NAME
link, unlink - Creates an additional directory entry for an existing file
SYNOPSIS
link file1 file2
unlink file
STANDARDS
Interfaces documented on this reference page conform to industry standards as follows:
link: XCU5.0
unlink: XCU5.0
Refer to the standards(5) reference page for more information about industry standards and associated tags.
DESCRIPTION
The link command performs the link() system call to create an additional directory entry for an existing file, file1. In effect, the
underlying file then has two names, file1 and file2 (either of these arguments can be a pathname). The old and new entries share equal
access rights to the underlying file.
The unlink command performs the unlink() system call to remove a link to file created by link. The unlink command removes the directory
entry specified by the file parameter and, if the entry is a hard link, decrements the link count of the file referenced by the link.
You should be familiar with the link() and unlink() system calls before you use these commands.
The link and unlink commands do not issue error messages when the associated system call is unsuccessful.
NOTES
The link and unlink commands cannot be used to link and unlink directories.
EXIT STATUS
The link and unlink commands both exit with the following: The link() or unlink() system call succeeded. Too few or too many arguments
specified. The link() or unlink() system call failed.
SEE ALSO
Commands: fsck(8), ln(1)
Functions: link(2), unlink(2)
link(1)